background image

 iv

GENERAL PRECAUTIONS 

Obey the following precautions for safe and correct usage.   
Precautions unique to the TM-2655/TM-2655P appear on the relevant page in this manual. Read the 
manual thoroughly before use. 

 

When installing and storing the device 

  Install or store the device away from moisture. 

  Do not install or store the device where the device may be badly affected by extreme temperature, 

humidity, direct sunlight, draft, dust, salinity or sulfur content in the air. 

  Do not install or store the device where chemicals, and corrosive or explosive gases are stored or 

present. 

  Install or store the device in a secure, level and stable location. 

  Install or store the device where adequate power is provided. (Where a medical 3P electrical outlet 

is provided.) 

 

Before use 

  Check to make sure the device operates safely and accurately. 

  Check all cables for proper connection. 

  When other medical equipment is used at the same time, a diagnostic error or dangerous situation 

may occur. Check all connections to make sure they do not interfere with each other. 

  When other telemeters are used, check that mutual interference will not cause a problem. 

 

During use 

  Check the patient and the device during use.   

 If medical or operational problems are found in the device or the patient, stop using the device 

immediately, check the status of the patient and take proper action. 

  Do not use the device during MRI scanning. 

  Do not use the device on a patient using a heart-lung machine. 

  High frequency interference by electrosurgery or energy discharged by a defibrillator may damage 

the device. Follow the precautions described in the manual for each device. 

  Do not use a cellular telephone near the device. It could affect the device’s operation. 

  The personal computer and medical equipment connected to the device are not allowed to be in the 

patient area. 

  The personal computer used must conform to IEC60950 

 

After use 

  Follow the predetermined procedure to return the operation switches to their original positions, and 

then turn off the power. 

  Do not forcibly pull out the cables. Hold the connector with your hand when disconnecting the cable. 

 Keep the device clean and in proper operating condition so that it can be used without problem 

during the next operation. 

  Clean the accessories and arrange them before storage. 

 

Environmental protection 

  Remove the built-in lithium battery from the device when the device is to be disposed of. 

  This device, any part of, and the built-in lithium battery are not treated as ordinary household waste, 

and must be disposed of according to the applicable regulations. 

Содержание tm-2655































Отзывы: