background image

 

 33 

[ 3 ] Press the        Up or Down key to select volume   

calibration data resetting mode. 

 
 
 

[ 4 ] Press the      Enter key to enter volume   

calibration data resetting mode.

 

 
 

[ 5 ] Press the        Up or Down key to select      .

 

(

  

 means YES and

   

 means NO.)

 

 

 

[ 6 ] Press the      Enter key to reset volume   

calibration data.   

 
 
 

[ 7 ] The Notice mark

     

is turned off to indicate   

that volume calibration data have reverted back   
to the factory default. 

 

 

11-3    Dispensing in a unit of weight 

(in mg unit) 

Dispensing of a liquid can be performed by weight (mg) instead of volume. (mg unit function) 
This function is useful when you handle a liquid that needs to be managed by weight,   
such as a diluted solution of a solid or powder. Although the density of a liquid can   
vary depending on the sample type and concentration, by weighing the dispensed 
amount with an electronic balance and inputting the result into the pipette, it becomes 
possible to easily dispense the liquid in a unit of weight (mg).

 

 

Selecting the mg unit   

The unit (volume: 

μ

L / weight: mg) for pipetting can be toggled by the following method.   

When the mg unit is selected, the Notice mark        blinks and the 

μ

L unit is turned off. 

* When the unit of weight (mg unit) is selected, perform weight calibration by the   

dispensing amount to be used. (The weight calibration data reverts back to the   
factory default once the unit is switched to

μ

L.)

 

   
 
 
 

Volume calibration data

resetting mode

 

Содержание MPA-10

























































Отзывы: