Analytik Jena PlasmaQuant PQ 9000 Скачать руководство пользователя страница 21

Страница: 21 / 76

Specification

PlasmaQuant PQ 9000

Edition 05/2014

3.2

Guidelines and standards

Safety class and safety type



The PlasmaQuant PQ 9000 belongs to safety class I.



The housing has safety type IP 20.

Device safety

The PlasmaQuant PQ 9000 conforms to the safety standards



DIN EN 61010-1 (VDE 0411T.1; IEC 61010-1)



DIN EN 61010-2-061 (IEC 61010-2-061)

EMC compatibility

The PlasmaQuant PQ 9000 has been tested for radio interference elimination and interference

immunity and fulfills the requirements stipulated by



DIN EN 61326

Environmental compatibility

The PlasmaQuant PQ 9000 has been tested for environmental compatibility and fulfills the

requirements stipulated by



DIN ISO 9022-3:2000



DIN ISO 9022-32-03-0



DIN ISO 9022-2:2003/01

EC directives

The PlasmaQuant PQ 9000 is built and tested according to standards that fulfill the

requirements stipulated by the EC directives 2006/95/EC and 2004/108/EC. Each device leaves

the manufacturer in a pristine and technically safe state. To maintain this condition and to

ensure safe operation, the operator must strictly observe the safety and operating instructions

contained in this manual. For accessories which have also been supplied, and system

components from other manufacturers, their operating instructions should be referred to.

Содержание PlasmaQuant PQ 9000













































































Результаты поиска

Содержание PlasmaQuant PQ 9000

Отзывы:

Похожие инструкции для PlasmaQuant PQ 9000

Бренды по названию

Популярные бренды

Analytik Jena PlasmaQuant PQ 9000, Руководство по эксплуатации

Результаты поиска

Содержание PlasmaQuant PQ 9000

Отзывы:

Похожие инструкции для PlasmaQuant PQ 9000

Бренды по названию

Популярные бренды