Analytic Systems BCD305-12-24 Скачать руководство пользователя страница 6

Страница: 6 / 12

Installation

MOUNTING

Mount the unit in a DRY location. Allow at least 1 inch of clearance for adequate cooling.

POWER CONNECTION

The unit is supplied with input power leads 1 meter long. This should normally be adequate to

connect to a source of power. If you must extend the cable:

• Use the smallest extension length possible.

• Use no less than 10 gauge conductors.

• Splice and solder the joints.

• Protect the joints with heat shrink tubing.

Connect the wires as follows:

• Red to Positive

• Black to Negative

POWER CONNECTION

Two positive output terminals and two negative output terminals are provided. Connect only

one wire to each terminal.

Note that the current specifications are for input current. To obtain the maximum output

current capability at any given input voltage, use the following formula:

Output Current = Input Volts / Output Volts x 26

For example:

10 VDC in and 27 VDC out, the max output current = 10/27 x 26 = 9.6 Amps.

20 VDC in and 27 VDC out, the max output current = 20/27 x 26 = 19.3 Amps

It is recommended to parallel the output connections if the unit is used as a single bank battery charger.

Содержание BCD305-12-24












