Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 281 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

4-17

Link Ports—ADSP-2146x

Interrupt Sources

Five types of interrupts are dedicated to link ports.

1. A DMA channel interrupt is generated when a DMA block transfer

through the link port with DMA enabled completes.

2. A DMA channel interrupt is generated when DMA for the link

buffer channel is disabled and the buffer is not full or the buffer is
not empty.

3. A link service request interrupt is generated when an external

source accesses the link port when the link port is disabled. (

LxTRQ

and

LxRRQ

). For example, if the enabled receiver wants to initiate a

data transfer with the disabled transmitter, it can make

LACKx

high.

When

LACKx

of the disabled link port goes high, then a link service

request interrupt is generated. Now the receiver can initiate the
transfer.

4. A link port invalid transmit

LPIT

is generated if the transmitter is

driving

LCLKx

high because the receiver has not asserted

LACKx

and

LCLKx

goes low due to a processor reset (or some other reason, even

though the receiver has not yet asserted

LACKx

). In this case, the

receiving link port generates an interrupt.

5. The transmitter generates an external transfer done interrupt once

the external transfer is completed. When DMA is not enabled, this
interrupt is generated when the transmitter FIFO is empty and the
last byte has been transmitted. If using DMA, the transmitter
checks if the DMA is complete.

Interrupt Service

All interrupts are latched and stored in the corresponding status register.
Whenever any of these four interrupts occur, the corresponding interrupt
LP0I or LP1I occurs if it is unmasked. In the ISR, the user should read the

www.BDTIC.com/ADI

«
...
279
280
281
282
283
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: Vanguard Страницы: 4

Бренд: CSS Страницы: 2

Бренд: Hama Страницы: 12

Бренд: TP-Link Страницы: 2

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

HiGain H2TU-R-402 List 7A

Бренд: ADC Страницы: 7

Бренд: Renesas Страницы: 28

EK-Quantum Momentum ROG Rampage VI Encore

Бренд: EK Страницы: 11

Бренд: C&T Solution Страницы: 129

EK-FC980 GTX Classy

Бренд: ekwb Страницы: 2

Бренд: INNOSILICON Страницы: 11

Бренд: NZXT Страницы: 2

Бренд: ZiLOG Страницы: 317

i.LON SmartServer

Бренд: Echelon Страницы: 34

ARC-12x4 Series

Бренд: Areca Страницы: 2

Бренд: Westermo Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды