UG-1308
Rev. A | Page 2 of 24
TABLE OF CONTENTS
Equipment Needed ........................................................................... 1
Documents Needed .......................................................................... 1
Software Needed ............................................................................... 1
General Description ......................................................................... 1
Evaluation Board Photograph ........................................................ 1
Revision History ............................................................................... 2
Power Configurations ...................................................................... 4
Direct 3.3 V Power via the AVDD and DVDD Connectors .. 6
Power via USB from 8-Pin DEBUG Connector (P27) ............ 6
Power via External 5 V Supply to 2-Pin Connector (P37) ..... 6
Connecting an Electrochemical Sensor ......................................... 7
Getting Started with the Tool Chain ............................................. 8
Installing the ADuCM355 Support Package ............................ 8
Running a GPIO Example in IAR Embedded Workbench ....8
Running a GPIO Example in Keil μVision ............................. 11
Application Examples .................................................................... 13
Cyclic Voltammetry Example .................................................. 13
EIS Example ................................................................................ 14
Chronoamperometry Example ................................................ 14
DC Current Example ................................................................. 15
4-Lead Electrochemical Sensor Example ................................ 16
AFE Die Watchdog Timer Example ........................................ 17
ADuCM355 System Calibration .................................................. 18
High Speed TIA Gain Resistor Calibration ............................ 18
Low Power TIA0/TIA1 Gain Resistor Calibration ............... 20
Mass Erasing a Device Not Responding to SWD Commands. 22
Ordering Information.................................................................... 23
Bill of Materials .......................................................................... 23
REVISION HISTORY
4/2021—Rev. 0 to Rev. A
Changes to Features Section, Equipment Needed Section,
Software Needed Section, and General Description Section ..... 1
Deleted MicroUSB Connector, P4 Setup Section Heading ........ 4
Changes to Power Configurations Section, MicroUSB Direct
Power via P4 and ADP7158 LDO Regulator Section, and
Figure 2 Caption ............................................................................... 4
Changes to Direct 3.3 V Power Via the AVDD and DVDD
Connectors Section, Jumper Setup with Direct 3.3 V Connection
Section, Power via USB from 8-Pin Debug Connector (P27)
Section, Jumper Setup with Power via USB Section, Figure 5
Caption, and Power via External 5 V Supply to 2-Pin Connector
(P37) Section ..................................................................................... 6
Changes to Connecting an Electrochemical Sensor Section ...... 7
Deleted Figure 8; Renumbered Sequentially ................................ 7
Changed Getting Started with the Tool Chain Section to
Getting Started with the Tool Chain Section ............................... 8
Changes to Downloading the Integrated Development
Environment (IDE) Section, Installing the ADuCM355 Support
Package Section, Running a GPIO Example in IAR Embedded
Workbench Section, and Project Folder Structure Section ........ 8
Replaced Figure 9 ............................................................................. 9
Changes to Compiling and Running Firmware Section and
Figure 11 Caption ........................................................................... 10
Replaced Figure 10 and Figure 12 ................................................ 10
Replaced Figure 14 ......................................................................... 11
Added Running a GPIO Example in Keil μVision Section,
Figure 15, and Figure 16; Renumbered Sequentially ................ 11
Deleted Figure 19 ........................................................................... 11
Added Figure 17 to Figure 19 ....................................................... 12
Changes to Application Examples Section, Cyclic Voltammetry
Example Section, and Figure 22 Caption .................................... 13
Added Figure 21 ............................................................................. 13
Changes to Figure 23 Caption, EIS Example Section, and
Chronoamperometry Example Section ...................................... 14
Replaced Figure 23 and Figure 25 ................................................ 14
Added Figure 24 ............................................................................. 14
Replaced Figure 28 and Figure 29 ................................................ 15
Changes to Figure 28 Caption and DC Current
Example Section ............................................................................. 15
Changes to 4-Lead Electrochemical Sensor
Example Section ............................................................................. 16
Added Figure 30 ............................................................................. 16
Moved Connecting an External Gain Resistor Across the High
Speed TIA Section, AFE Watchdog Timer Example Section,
and Figure 32 .................................................................................. 17
Changes to AFE Die Watchdog Timer Example Section ......... 17
Added ADuCM355 System Calibration Section ....................... 18
Moved High Speed TIA Gain Register Calibration Section ..... 18
Deleted Figure 29 ........................................................................... 18
Changes to High Speed TIA Gain Resistor
Calibration Section ......................................................................... 18
Deleted Figure 33 ........................................................................... 18
