background image

UG-949 

EVAL-AD7761FMCZ User Guide 

 

Rev. 0 | Page 14 of 17 

SOFTWARE OPERATION 

14323-

1

16

 

Figure 16. Evaluation Software Main Window 

Overview of the Main Window 

The main window contains the significant control buttons and 
analysis indicators of the evaluation software. 

Configuration Tab and 

AD7761

 Block Diagram 

The 

Configuration

 tab is the tab displayed by default when the 

software first opens. An overview of the 

AD7761

 block diagram 

is shown, along with buttons that open pop-up menus for quick 
configuration of the device.  
The 

Waveform

 tab displays captured waveform data. It also 

contains options to save the resulting data and shows the output 
header data from the conversion results. 
The 

FFT

 and 

Histogram

 tabs show a more in depth analysis of 

the output data. This data can be saved to a file. 
Use the 

Registers

 tab to change the configuration of the 

AD7761

Sample Button 

Click 

Sample

 to start ADC sampling; results are reported in the 

Waveform

FFT

, and 

Histogram

 tabs. Set the mode of 

operation using the 

Sampling

 

Mode

 drop-down menu; the 

mode can be continuous sampling or a single run. 

Number of Samples 

The number of samples per channel is variable and can be 
changed using the 

Samples

 control. 

MCLK 

The 

MCLK (Hz)

 control in the 

Configuration

 tab must match 

the frequency of the ADC clock source. 

V

REF

 

The 

Ext. REF (V)

 box in the 

Configuration

 tab control must 

match the reference voltage of the ADC. 

ADC Reset 

Clicking 

ADC Reset

 in the 

Configuration

 tab sends a reset 

command to the ADC via the SPI, and resets the device to its 
default configuration. 

Header Data 

The 

Header Data 

area shows the header data output in the first 

eight bits of a conversion. It conveys status information and the 
channel number. Header data for each channel can be selected 
by changing the 

Analysis Ch

 option.  

 

Filter saturated

 indicates that filter saturation has occurred.  

 

Filter Type

 indicates the type of filter that is selected.  

 

Filter not settled

 indicates that the filter did not settle 

before data was sampled. 

 

CRC Error

 indicates that a cyclic redundancy check error 

has occurred, and a reset is required. 

Note that the evaluation software is not configured to output 
the CRC code. 

14323-

016

 

Figure 17. Example Header Data 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Содержание EVAL-AD7761FMCZ


















Отзывы: