Analog Devices ADSP-21261 SHARC Скачать руководство пользователя страница 225 | Manualshive

Страница: 225 / 846

background image

ADSP-2126x SHARC Processor Hardware Reference

5-21

Memory

Illegal I/O Processor Register Access

The DSP monitors I/O processor register access when the Illegal I/O pro-
cessor Register Access (

IIRAE

) bit in the

MODE2

register is set (=1). If access

to the IOP registers is detected, an Illegal Input Condition Detected
(

IICDI

) interrupt occurs. The interrupt is latched in the

IRPTL

register

when a core access to an IOP register occurs.



The I/O processor’s DMA controller cannot generate the

IICDI

interrupt.

For more information, see “Mode Control 2 Register

(MODE2)” on page A-7.

Unaligned 64-Bit Memory Access

The DSP monitors for unaligned 64-bit memory accesses if the Unaligned
64-bit Memory Accesses (

U64MAE

) bit in the

MODE2

register (bit 21) is set

(=1). An unaligned access is an odd numbered address normal word access
that is forced to 64 bits with the

LW

mnemonic. When detected, this con-

dition is an input that can cause an Illegal Input Condition Detected
(

IICDI

) interrupt if the interrupt is enabled in the

IMASK

register.

information, see “Mode Control 2 Register (MODE2)” on page A-7.

The following code example shows the access for even and odd addresses.
When accessing an odd address, the sticky bit is set to indicate the
unaligned access.

bit set mode2 U64MAE; /* set testbit for aligned or

unaligned 64-bit access*/

r0 = 0x11111111;

r1 = 0x22222222;

pm(0x80200) = r0(lw); /* even address in 32-bit, access

is aligned */

pm(0x80201) = r0(lw); /* odd address in 32-bit, sticky

bit is set */

«
...
223
224
225
226
227
...
»

Содержание ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-21261 SHARC

Бренд: GE Страницы: 93

Бренд: Commell Страницы: 58

Бренд: Garland Страницы: 6

TD-3316B4-16P-A1

Бренд: TVT Digital Страницы: 2

Бренд: Multitech Страницы: 81

Бренд: Disc Makers Страницы: 38

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Бренд: AMD Страницы: 27

Бренд: EXAGATE Страницы: 7

EK-Quantum Vector TUF RX 6800

Бренд: ekwb Страницы: 14

STM32MP157 Series

Бренд: ST Страницы: 47

Бренд: TERSUS Страницы: 7

EK-Quantum Vector FE RTX 3080

Бренд: ekwb Страницы: 20

3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...

Бренд: 3Com Страницы: 6

Бренд: B&B Electronics Страницы: 90

Бренд: Data-Tronix Страницы: 15

234664-002 - ProLiant - ML330T02

Бренд: Compaq Страницы: 160

Бренд: StarTech.com Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды