Installation Guide
NXA-BASE/1
Battery Base Kit for 7" & 10" Modero
®
Table Top Touch Panels
Overview
The NXA-BASE/1 Battery Base Kit (FG2255-05K) provides both power and
battery information to the panel through the panel’s interface connector. The
battery base allows the 7” and 10” Modero Table Top Touch Panels to run off the
charge from a single internally connected NXT-BP Battery Pack.
Can be charged through either the base (only when connected to the panel) or
through an optional NXT-CHG Quick Charger Kit. When used with the battery
base, the panel will charge the battery during full operation.
Features
• Charge current 2.4A @ 12 VDC
• Charge time for one depleted battery ~ five to eight hours
• The Modero unit plus battery base requires a PSN4.4 power supply
ATTENTION!
Verify that the Modero panel is using the latest firmware. Verify that the battery
base is loaded with the latest NXA-BASE/1 firmware.
Specifications
Checking the NXT-BP Charge
Note
: It is recommended to fully charge this battery before using it to power an
NXT-CV7 panel.
1.
Press the Battery Life Indicator button (FIG. 1) once to illuminate the
Battery Life LEDs and display the percent charge remaining on the battery
(
this indication lasts a few seconds
).
2.
Charge the NXT-BP battery by either inserting it into the battery base or
from within the optional NXT-CHG charger (which can sequentially charge
up to two batteries).
ATTENTION
!
If the 25% LED indicator is blinking, recharge your battery immediately. This
blinking indicates there is less than 5% of a charge remaining on the battery.
Installation of an NXT-BP into the NXA-BASE/1
The base does not directly connect to a power supply. Instead, it receives the
power necessary to charge the battery from the Modero panel (through the
Panel Interface connector).
1.
Install the NXT-BP battery into the battery compartment, label-side up.
2.
Align the battery connector with its corresponding battery connector port
(located in the battery compartment shown in FIG. 2).
3.
Carefully insert the NXT-BP into the base until the battery securely fits onto
the Battery Connector Port.
FIG. 1
NXA-BASE/1 Kit (NXA-BASE/1 & NXT-BP)
Alignment Peg
Alignment Peg
Battery Lock
Battery Latch
Slider
Insert holes for Touch Panel
Insert holes for Touch Panel
Panel Connector
Securing Pegs
NXT-BP
Battery Connector Port
Battery Life (Charge)
Battery Life Indicator
push button
Charge batteries fully before initial use.
Battery Connector
NXA-BASE/1 Kit Specifications
Included:
• (1) NXA-BASE/1: FG2255-05
• (1) NXT-BP: FG2255-10
Dimensions (HWD):
• NXA-BASE/1: 7/8” x 6” x 6 7/8”
(2.36 cm x 15.14 cm x 17.51 cm)
• NXT-BP: 3/4” x 3 1/2” x 5 3/4”
(1.75 cm x 8.89 cm x 14.76 cm)
Weight:
• Base unit: 12 oz (340 g)
• NXT-BP: 1.0 lbs (450 g)
• Base and 1 battery: 1.75 lbs (790 kg)
Power:
• NXA-BASE/1: 1.4 A @ 12 VDC (max power draw while
charging a single battery)
• NXT-BP: Voltage - 11.1 Volts (nominal)
Operating / Storage
Environment:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage/Discharge Temperature: -20° C (-4° F) to 60° C
(140° F)
• Storage Humidity: 5% - 85% RH
Included
Accessories
• Rubber Foot Placement Template (68-2255-02)
• 4 Rubber Feet (45-0013-04)
FIG. 2
Battery installation procedure
