For full warranty information, refer to www.amx.com.
6/07
©2007 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-40-813
REV: A1
To adjust an AF-10 RX board for cable length:
1.
Remove the screws at the top and bottom of the board’s faceplate.
2.
Push down on the board extractor handle and pull the board out.
3.
Set toggles (1-2-3-4) on both DIP switches (a small screwdriver or paper clip
works well) to the correct position according to the table on the previous page.
Both DIP switches must be set to the same value.
4.
Push the board back into position (handle will snap into place); replace screws.
Installation
Important: Always use a UL approved power source. Check the power source’s
documentation for information specific to that power source.
To attach connectors & power to the TX and RX:
1.
Adjust the RX for line length if necessary (see previous procedure for RX cable
length adjustment).
2.
Insert, attach, or wire the connectors to the TX and RX as shown in FIG. 5 and
FIG. 6 or 7.
3.
Insert the RJ-45 connector into the CAT-5 receptacle (see FIG. 5).
4.
Module – Plug power cord into the power jack and into the power source.
AF-10 – Plug power cord into the power receptacle and into the power source.
Video Connectors
Video connectors are available in BNC, RCA (video not shown), or S-Video.
Note: AMX AutoPatch S-Video cables lock onto S-Video connectors. Standard
S-Video cables may be used, but will not lock. Hold the connector at a slight angle to
the right while pushing in or pull back on the connector housing while pushing in.
Audio Connectors
Audio connectors are either 3-position terminal block (balanced/unbalanced – FIG. 6;
unbalanced – FIG. 7) or RCA (unbalanced – FIG. 5).
Important: To determine the correct wiring to use for the audio connectors, check
the type of connection specified in the tables in the column to the right. If the model is
listed for balanced audio, it may also be wired for unbalanced audio (FIG. 6). If the
model is listed for unbalanced, it can only be wired for unbalanced (FIG. 7).
Note: When using twisted-pair wire, connect the shield (ground) at one end only
(recommend receiving end) to minimize low frequency noise.
TX & RX Model Numbers
* High headroom – up to a +22 dBu signal.
FIG. 4
Set toggles on both DIP switches to the same value
FIG. 5
Insert or attach video connectors as shown in sample boards
FIG. 6
Wiring for models with 3-position balanced audio connectors (see tables to right)
FIG. 7
Wiring for models with 3-position unbalanced audio connectors (see table below)
2 3 4
0
2 3 4
0
2 3 4
0
Example shows a setting
of “0-1-0-0” for a cable length
of 425 ft. (130 m)
The “1” side
The “0” side
RJ-45
RJ-45
BNC
S-Video
RCA
Audio
(see below)
FG1040-443
FG1040-413
(audio)
Signal
Jumper
Common
Non-Inverting Signal
Inverting Signal
Shield
Balanced Wiring
Unbalanced Wiring
Signal
Common
Unbalanced Wiring
CAT-5 S-Video+Stereo TX & RX Modules
FG1010-37
TX, S-Video / RCA unbalanced
FG1010-43
TX, S-Video / 3-position unbalanced
FG1010-49
TX, BNC / RCA unbalanced
FG1010-55
TX, BNC / 3-position unbalanced
FG1010-61
TX, RCA / RCA unbalanced
FG1010-64
TX, BNC / 3-position balanced (HH)*
FG1010-03
TX, S-Video / 3-position balanced (HH)*
FG1010-34
RX, S-Video / RCA unbalanced
FG1010-40
RX, S-Video / 3-position unbalanced
FG1010-46
RX, BNC / RCA unbalanced
FG1010-52
RX, BNC / 3-position unbalanced
FG1010-58
RX, RCA / RCA unbalanced
FG1010-67
RX, BNC / 3-position balanced (HH)*
FG1010-00
RX, S-Video / 3-position balanced (HH)*
CAT-5 S-Video+Stereo TX & RX AF-10 Boards
FG1040-410
TX, RCA / RCA unbalanced
FG1040-413
TX, S-Video / RCA unbalanced
FG1040-416
TX, S-Video / 3-position unbalanced
FG1040-419
TX, BNC / 3-position unbalanced
FG1040-422
TX, BNC / RCA unbalanced
FG1040-440
TX, S-Video / 3-position balanced (HH)*
FG1040-443
TX, BNC / 3-position balanced (HH)*
FG1040-425
RX, RCA / RCA unbalanced
FG1040-428
RX, S-Video / RCA unbalanced
FG1040-431
RX, S-Video / 3-position unbalanced
FG1040-434
RX, BNC / 3-position unbalanced
FG1040-437
RX, BNC / RCA unbalanced
FG1040-446
RX, S-Video / 3-position balanced (HH)*
FG1040-449
RX, BNC / 3-position balanced (HH)*
