Installation Guide
DTV-RX02-HD
Digital TV Receiver High Definition
Overview
As part of an AMX TDS (Television Distribution System) installation, the DTV-RX02-HD
High-Definition Receiver (
FG1411-02
) is located at the display to receive an incoming digital
TV signal from a DTV Transmitter, and convert it to a compatible HD format for the display
(FIG. 1).
Trademark Acknowledgement
The design of the DTV-RX02-HD was approved by Dolby™. Manufactured under license
from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
Product Specifications
Supported Output Resolutions
Subtitle Support
DTV-RX02-HD Receivers do not support the display of subtitles.
AMX TDS System Description
The AMX TDS system can be deployed in any installation where digital A/V broadcast over IP
is desired, and delivers Digital TV and other encoded A/V signals to a number of TV sets, or
desktop PC's.
System Components
The AMX TDS system consists of several components, including a DTV-MA01 TDS
Management Appliance, Receiver (and IR Remote Controller), and Transmitter. See the
AMX
TDS Operation/Reference Guide
for details.
Network Considerations
Because of the high bandwidth associated with A/V distribution, the TDS system is typically
managed via a separate IT infrastructure. However, content may be streamed over the main
network if desired. Consult your IT representative to determine the proper network
configuration for the TDS system.
The AMX TDS system transmits audio/video using IP multicast. In order for this to work
satisfactorily, it is vital that the network switches are multicast-enabled in order to prevent
unwanted flooding of traffic on the network.
•
Within the context of AMX TDS documentation. the term “Multicast-enabled” means
that all network switches carry out IGMP snooping, and one switch must function as the
IGMP querier.
•
AMX Digital TV supports version 2 of IGMP.
Front Panel Components
External IR Receiver Socket
Use the External IR Receiver socket on the front panel to connect the included External IR
Receiver (60-1411-01).
The IR Receiver provides wired IR control of the RX02.
IR Receiver
The IR Receiver on the front panel allows the DTV-RX02-HD to use the DTV-RC01 Digital TV
Remote Control (included) for channel selection and control of local monitor volume and
power.
Rear Panel Connectors
All connectors are located on the rear panel of the DTV-RX02-HD, for ease of installation and
easy access. Refer to FIG. 1 for the connector layout.
10/100 Port
The 10/100 (RJ45) port on the rear panel provides 10/100 BaseT network connectivity.
Network Port Pinouts and Signals
The following table lists the pinouts, signals, and pairing for the 10/100 Network port.
Note
: The maximum distance that a Receiver can be mounted from the Network Switch is
100m (328’).
Consult the Network Administrator for correct cabling from the DTV-TX Transmitter onto the
network.
•
For remote connectivity, the Firewall may have to be configured to open port
2008
for
remote connectivity over UDP.
•
For remote connectivity, the Receivers will use ports
2008
,
5000
,
5001
,
5002
and
5003
for remote connectivity over UDP.
Ethernet LEDs
Default IP Address
By default, DTV Receivers are set to
DHCP
. See the
Setting the Receiver’s IP Address via
the RS 232 Port
section for more information.
Audio Output Connectors
•
Analog
: Standard red and white AUDIO RCA connectors provide analog stereo audio
output (White = Left, Red = Right).
•
Digital
: The orange SPDIF RCA connector provides digital audio output.
Video Output Connectors
•
VGA:
The 15-pin VGA connector provides Component video output.
•
CVBS
: The yellow CVBS RCA connector provides Composite video output.
•
HDMI:
The HDMI connector provides HDMI video output.
FIG. 1
DTV-RX02-HD Receiver
DTV-RX02-HD Receiver
Dimensions (HWD):
1" x 10.5" x 4.25" (2.54 cm x 26.67 cm x 10.76 cm)
Weight:
0.90 lbs (0.41 kg)
Power:
• Input Voltage 12VDC
• Power Dissipation 6~10 Watts
Front Panel Components
IR Receiver:
For use with the DTV-RC01 Digital TV Remote Control (included).
External IR
Receiver Socket
Connects to the External IR Receiver (included).
USB Ports
not used
Rear Panel Connectors
10/100 (RJ45):
Standard 10/100 Network (RJ45) connector.
Note
: The DTV-RX02-HD does not support PoE power.
AUDIO / VIDEO
OUT Connectors:
• COMPONENT: 15-pin connector provides component video output.
• CVBS: RCA connector provides composite video output.
• L / R Stereo: RCA connectors provide L/R analog audio output.
• SPDIF: RCA connector provides digital audio output.
• HDMI: HDMI connector provides HDMI video output.
RS232 (DB9):
Serial connector for local command line interface (RS232 only).
Mainly used for control of TV, and can be used for changing IP.
POWER:
Barrel plug accepts 12VDC power from the included power supply.
Note
: This connector is intended to be used only with the provided
power supply.
Operating
Environment:
• Temperature: 35°F - 95°F (5°C - 35°C)
• Humidity: Max. relative humidity - 85% (non-condensing)
Certifications:
• CE
• FCC part 15 Class A
Included Accessories:
• 12 VDC Power Supply
• DTV-RC01 Digital TV Remote Control (FG1411-70)
• External IR Receiver (60-1411-01)
Other AMX Equipment:
• DTV-MA01 TDS Management Appliance (FG1412-01)
• DTV-TX01-DVB-T Transmitter (FG1410-01)
• DTV-TX02-DVB-S Transmitter (FG1410-02)
• DTV-TX03-US Transmitter (FG1410-03)
• CC-232 Serial Communication Cable (FG10-752-04)
DTV-RX02-HD Receivers - Supported Output Resolutions
• 1920 x 1080p / 60Hz (*)
• 1080p / 50Hz (*)
• 1920 x 1080i / 60Hz (*)
• 1080i / 50Hz (*)
• 1280 x 720p / 60Hz (*)
• 720p / 50Hz (*)
• 480p / 60Hz
• 576p / 50Hz (*)
• 480i / 60Hz
• 576i / 50Hz (*)
Note
: The asterisk (*) indicates dual output with HDMI/Component
CVBS digital video Out
SPDIF digital audio Out
Analog audio Out (L/R)
(front)
IR Receiver
RS232 Serial connector
(DB9: for local device control only)
PWR connector
10/100 (RJ45) Ethernet
connector (to network)
Component video Out
HDMI video Out
not used
(rear)
External IR Receiver socket
RJ45 Network Port Pinouts and Signals
Pin
Signals
Connections
Pairing
Color
1
TX +
1 --------- 1
1 --------- 2
Orange-White
2
TX -
2 --------- 2
Orange
3
RX +
3 --------- 3
3 --------- 6
Green-White
4
no connection
4 --------- 4
Blue
5
no connection
5 --------- 5
Blue-White
6
RX -
6 --------- 6
Green
7
no connection
7 --------- 7
Brown-White
8
no connection
8 --------- 8
Brown
FIG. 2
Ethernet LEDs
SPD
- Speed LED
connection speed is 100 Mbps
and turns Off when speed is
lights (yellow) when the
L/A
- Link/Activity LED
lights (green) when the
Ethernet cables are
connected and terminated
10 Mbps.
correctly.
