Installation and Setup
46
Enova Digital Media Switchers - Hardware Reference Manual
IMPORTANT:
Before connecting a Solecis Digital Switcher to a DXLink Twisted Pair Input Board in an Enova DGX 100 Series
Digital Media Switcher, both the Solecis unit and all DXLink Twisted Pair boards must be upgraded with the latest available
firmware versions. Solecis units must be upgraded before connecting a unit to an upgraded input board.
Options for System Setup with DXLink Twisted Pair 4K
The following table contains the options in an Enova DGX Switcher for using DXLink Twisted Pair 4K Input and Output
Boards in conjunction with DXLink Twisted Pair 4K Transmitters and Receivers:
NOTE:
Additional compatibility is available between DXLink Twisted Pair 4K and DXLink Twisted Pair equipment (see the
DXLink Twisted Pair 4K Transmitters & Receivers Hardware Reference Manual
).
Options for System Setup with DXLink Fiber
The following table contains the options for using DXLink Fiber Input and Output Boards in conjunction with DXLink Fiber TXs
and RXs in an Enova DGX Digital Media Switcher. The input/output boards and TX/RX units can be either Duplex or
Simplex, as long as the model types match (multimode to multimode and single mode to single mode).
IMPORTANT:
Compatibility between hardware requires matching model types: multimode to multimode and single mode
to single mode.
NOTE:
A typical system setup for a source and destination is illustrated on FIG. 53 on page 139.
Unpacking
Enova DGX Switchers are shipped with one enclosure per shipping box. The invoice is sent separately; a packing slip is
attached to the outside of each box.
Each box contains the following items:
Enova DGX 100 Series Digital Media Switcher
US power cords (if shipped within the US): Two provided with the DGX 800/1600/3200, four are provided for the
Enova DGX 6400
Other enclosure related products as needed
NOTE:
For orders comprising multiple enclosures, the shipping boxes are marked as "Chassis __ of __," where the first blank
is the box number and the second blank is the total number of boxes in the shipment.
Unpacking Tips
Before fully unpacking the enclosure,
inspect the shipping box for any signs of damage
. If a box is partially crushed
or any sides have been broken open, notify the shipping agency immediately and contact your AMX
representative (see the warranty at www.amx.com).
Once unpacking is complete, closely check the physical condition of the enclosure.
Collect all documentation.
NOTE:
Please save the original shipping container and packing materials. AMX is not responsible for damage caused by
insufficient packing during return shipment to the factory. Shipping boxes are available; contact your AMX representative
for details.
System Setup Options - Enova DGX Boards with DXLink Modules/Wallplates
DXLink Wallplate
Enova DGX Input Board
Enova DGX Output Board
DXLink Module
HDMI 4K Decor Wallplate TX
→
DXLink Twisted Pair
→
DXLink Twisted Pair
→
HDMI 4K RX Module
HDMI 4K Decor Wallplate TX
→
DXLink Twisted Pair
→
Any output board
→
Not applicable
Not Applicable
Any input board
→
DXLink Twisted Pair
→
HDMI 4K RX Module
System Setup Options - Enova DGX Boards with DXLink Fiber
DXLink Fiber TX
DXLink Fiber Input Board
DXLink Fiber Output Board
DXLink Fiber RX
Multi-Format MM Fiber TX
→
Multimode Fiber
→
Multimode Fiber
→
HDMI MM Fiber RX
Multi-Format MM Fiber TX
→
Multimode Fiber
→
Single Mode Fiber
→
HDMI SM Fiber RX
Multi-Format MM Fiber TX
→
Multimode Fiber
→
Any output board
→
Not applicable
Multi-Format SM Fiber TX
→
Single Mode Fiber
→
Single Mode Fiber
→
HDMI SM Fiber RX
Multi-Format SM Fiber TX
→
Single Mode Fiber
→
Multimode Fiber
→
HDMI MM Fiber RX
Multi-Format SM Fiber TX
→
Single Mode Fiber
→
Any output board
→
Not applicable
Not Applicable
Any input board
→
Multimode Fiber
→
HDMI MM Fiber RX
Not Applicable
Any input board
→
Single Mode Fiber
→
HDMI SM Fiber RX
