Programming
54
AXB-TPI/3 Touch Panel Interface 3
Shorthand Send_Commands (Cont.)
@MOU
Sets the serial
touch interface
type.
When changing the serial touch device, connect the hardware before setting the device
type. Refer to the
section on page 79 for more information.
Syntax:
"'@MOU <touch_type>'"
Variables:
touch type =
00: Touch OFF
01: Microsoft
®
serial mouse (PC Presenter)
02: Second Microsoft
®
serial mouse (MX-MM MobileMouse)
10: Dynapro
®
mouse
11: MicroTouch
®
12: Elo IntelliTouch
®
touch monitor (G3 touch panels)
13: Elo AccuTouch
®
touch monitor and VTM-D15/A MultiMedia Touch Panel
15: EZ Screen
®
touch monitor
8000: Touch Output to Serial Port (Elo IntelliTouch)
FF: External touch driver
Example:
SEND COMMAND Panel,"'@MOU 11'"
Sets the touch interface to MicroTouch.
Touch Output to Program Port 80xx. Touch Output Pass Through C0xx where
xx
is the
specific mouse driver from the above list.
• 80xx sends touches to the current TPI/3 screen and out the Program Port.
• C0xx sends touches only out the Program Port, not to the current TPI/3.
Note: Bit 15: When Touch Output to Program port is used, Program port baud rate is the
same as Mouse port baud rate.
Note: Bit 13: When Reverse Touch to Mouse port is used, all serial communications on the
Program port are disabled.
Example:
SEND_COMMAND TP,"’@MOU E011'"
<touch type> where xx is the specific touch mode from above.
Bit 15: Touch Output to Program Port
Bit 14: Touch Data NOT used on this TPI/3
Bit 13: Reverse Touch to Mouse Port
Bit 12-8: Undefined
Bits 15 14 13 12-8 Definition
00xx 0 0 0 0 0000
20xx 0 0 1 0 0000
40xx 0 1 0 0 0000
60xx 0 1 1 0 0000
80xx 1 0 0 0 0000
A0xx 1 0 1 0 0000
C0xx 1 1 0 0 0000
TPI/3 uses Touch Device data from the Mouse port.
TPI/3 uses Touch Device data from the Mouse port
and sends Program Port data to the Mouse Port.
TPI/3 doesn’t use Touch Device data from the Mouse
port (all touch input/output disabled).
TPI/3 doesn’t use Touch Device data from the Mouse
port ands sends Program port data to the Mouse port.
TPI/3 uses Touch Device data from the Mouse port,
sends its data to the Program port, and sends Program
port data to the Mouse Port.
TPI/3 uses Touch Device data from the Mouse port,
sends it s data to the Program port.
E0xx 1 1 1 0 0000
TPI/3 doesn’t use Touch Device data from the Mouse
port and sends its data to the Program port.
TPI/3 doesn’t use the Touch Device data from the Mouse
port, sends its data to the Program port, and sends
Program port data to the Mouse port.
Содержание AXB-TPI/3
