Quick Start Guide
AutoPatch CAT-5 RGBHV
TX & RX
Overview
The CAT-5 RGBHV Transmitter (TX) and Receiver (RX) work together or work in
conjunction with CAT-5 RGBHV boards on an AMX AutoPatch Distribution Matrix. This
guide contains complete information for the TX and RX when used as a pair. Product
model numbers vary depending on the type of installation and length of cable (see
table below). For additional information on using modules or boards in conjunction with
a distribution matrix, see the distribution matrix’s instruction manual on the AMX
AutoPatch Software & Documentation CD or visit www.amx.com. For adding or
replacing boards on the AF-10 and for AF-10 specifications, see the “AF-10 Quick
Start Guide.”
TX & RX Installation Types
Transmitters and Receivers pairs are available for two types of installation.
•
Transmitter-to-Receiver: TX passes source signal directly to RX
•
Transmitter-to-Matrix-to-Receiver: TX passes source signal to a
distribution matrix, which routes the signal to a corresponding RX (allowing
for switching to multiple destinations)
Each type of TX is tuned to work with a corresponding RX installation type. A TX of
one type must be used with an RX of the same type. Use the table below to determine
TX and RX installation types.
Specifications
Cable Requirements
Use any of the following UTP cable: CAT-5, CAT-5e, CAT-6, or skew-free.
The cable length must equal the specified distance for the receiver (see the first table
in the column to the left); extra cable may be required to achieve the receiver’s
specified length. Cable is available in fixed lengths.
Each cabled TX and RX pair allows up to 300 ft. (91.44 m) to maintain specifications.
Total distance must be <400 ft. (121.92 m).
Important: The recommended skew ratio for all cable is <25 nS per 328 ft. (100 m).
System Setup
A typical setup using a Transmitter-to-Receiver CAT-5 RGBHV TX and RX is
illustrated in FIG. 2. The modules and AF-10 boards may be mixed in four different
ways (see the “combinations” list in FIG. 2).
A typical setup using a Transmitter-to-Matrix-to-Receiver CAT-5 RGBHV TX and RX is
illustrated in FIG. 3. The modules and AF-10 boards may be mixed in four different
ways (see the “combinations” list in FIG. 3).
FIG. 1
CAT-5 RGBHV TX & RX are available as modules & AF-10 boards (see table below)
TX & Corresponding RX Installation Types
TX
RX
Transmitter-to-Receiver
FG1010-82, Module
FG1040-467, AF-10
FG1010-73 (100 ft., 30.48 m), Module
FG1010-76 (200 ft., 60.96 m), Module
FG1010-79 (300 ft., 91.44 m), Module
FG1040-458 (100 ft., 30.48 m), AF-10
FG1040-461 (200 ft., 60.96 m), AF-10
FG1040-464 (300 ft., 91.44 m), AF-10
Transmitter-to-Matrix-to-Receiver
FG1010-85, Module
FG1040-470, AF-10
FG1010-88 (25 ft., 7.62 m), Module
FG1010-91 (100 ft., 30.48 m), Module
FG1010-94 (200 ft., 60.96 m), Module
FG1010-97 (300 ft., 91.44 m), Module
FG1040-473 (25 ft., 7.62 m), AF-10
FG1040-476 (100 ft., 30.48 m), AF-10
FG1040-479 (200 ft., 60.96 m), AF-10
FG1040-482 (300 ft., 91.44 m), AF-10
General Specifications
Approvals
CE, UL, cUL
Signal Type
RGBHV
Supported Cable Types
CAT-5, CAT-5e, CAT-6
Power Consumption (max.)
& Connector – Module
+12 V - +24 V DC @ 5 Watts
2.1 mm DC power jack
Power Consumption (max.) – AF-10
120 VAC / 240 VAC, 50 - 60 Hz
Humidity
0 to 90% non-condensing
Operational Temperature
32° - 110° F (0° - 43° C)
Dimensions – Module
5.22 in. (13.26 cm) depth
5.82 in. (14.78 cm) width
1.42 in. (3.61 cm) height w/out feet
Weight – Module
Approximately 1.5 lb. (0.68 kg)
Connectors
RJ-45 and HD-15
10-82
10-79
CAT-5 RGBHV TX Module
CAT-5 RGBHV RX Module
CAT-5 RGBHV
AF-10 Boards
(not to scale)
Video Specifications
Input Level (max.)
+/-1 V
Input Impedance
75 ohms
Output Level (max.)
+/-1 V
Output Impedance
75 ohms
HV Sync Input/Output
TTL
Resolution
From VGA (640x480) to UXGA (1600x1200 @ 60 Hz)
over all distances
<
400 feet
Typical Bandwidth
150 MHz @ +/-3 dB over 300 ft. (91.44 m) of CAT-5 cable
(module to module)
FIG. 2
System setup for a Transmitter-to-Receiver type installation
FIG. 3
System setup for a Transmitter-to-Matrix-to-Receiver type installation
10-XX
10-XX
Four combinations are possible:
Module TX -> Module RX (illustrated)
Module TX -> AF-10 RX
AF-10 TX -> Module RX
AF-10 TX -> AF-10 RX
120V
AC
/240V
AC
25 W
att /
2
A
Max.
10-XXX
IN
11
10
9
12
IN
15
14
13
16
IN
19
18
17
20
8
IN
7
6
5
IN
3
2
1
4
IN
24
23
22
21
24
OUT
22
23
21
8
OUT
5
6
7
12
OUT
9
10
11
16
OUT
13
14
15
20
OUT
17
18
19
4
OUT
1
2
3
Four combinations are possible:
Module TX -> matrix -> Module RX
Module TX -> matrix -> AF-10 RX
AF-10 TX -> matrix -> Module RX (illustrated)
AF-10 TX -> matrix -> AF-10 RX
