background image

13

9. PUMP PROTECTION AND DIAGNOSTICS

The Well-X1

 continually monitors pressure, cycle time and voltage to protect the well pump. The following error codes 

alert the user to a potential problem, prompting service.

E1

: Rapid Cycle

E2

: Low Suction (low water cut-off)

E3

: Voltage Protection

E5

: Improper Wiring

WELL-X1

 ERROR CODES

When an error occurs, the display will flash a diagnostic code and emit an audible chirp.

ERROR CODE

POSSIBLE CAUSES AND CONTROL ACTION

E1

: Rapid Cycle

Multiple cycles below a safe runtime indicate an incorrect 
precharge, undersized Well-X1

 or waterlogged tank. Pump 

continues to run.

E2

: Low Suction

Pump operation below 10 psi indicates a low well level, well 
piping leak, insufficient prime, failing pump or loose wiring. 
Pump will shut  down and attempt to restart every 60 minutes.

E3

: Voltage Protection

If line voltage varies outside a safe operating range, low or 
high, the control will run for up to two minutes to ensure water 
is available, then shut the pump off until voltage is restored to 
a normal range.

E5

: Improper Wiring

This error indicates the LINE and LOAD wiring is reversed at 
the Well-X1

. Correct wiring to allow proper operation.

NOTE: E4 is not used with the Well-X1

.

Содержание WELL-X-TROL

















Отзывы: