Quick Reference Guide
XLR8/XLR8 Plus
Features
Therapy Mode
“C” = Continuous
“V” = Variable
Target Pressure
Battery Indicator
USB Entry
Used for engineering
purposes only.
Actual Pressure
This number will naturally
fluctuate above and below
target pressure.
Suction Strength
Green Bars = seal is adequate
Red Bars =
seal may be compromised
System Status
Green Check (
) =
proper function
Red Exclamation (
!
) = problem
On/Off Button
Up/Down Arrow Buttons
Press in main screen to increase/decrease pressure setting.
In Menu/Select screen, press to scroll through menu and
implement functions.
Lock/Unlock Button
Power Jack Inlet
Used to charge unit.
Keypad Lock/Unlock
Status
Red = Locked
Green = Unlocked
Time and Date
Menu/Select Button
Press to silence or lock in
user changes.
Exit/Cancel Button
Press to go back to previous,
or main screen.
Treatment Time
Indicates time therapy
has been in progress.
Service needed
6 month PM or 4000 hour
check recommended.
XLR8/XLR8 Plus
Quick Reference Guide
Application Guide
XLR8/XLR8 Plus
Questions?
Call 1.800.208.2025 or 516.217.0010 | email [email protected] | www.genadyne.com
©2016 Genadyne Biotechnologies, Inc. CLN-003 02/16
Step 1
Select appropriate size dressing kit for
wound. Kit contains foam, port pad,
and 2 drapes. (Small kit has
1 drape only.)
Step 2
Clean the wound according to protocol.
Protect wound edges with drape.
Step 3
Cut foam to fit accurately in wound
bed. Avoid overlapping onto intact
skin. Avoid cutting foam over wound.
Avoid over-packing, as this will inhibit
filtration of drainage.
Step 4
Cover foam with drape by separating
bottom layers 1 and 2 to expose the
adhesive drape. Position and place
drape over foam. Remove stabilization
layers 1 and 2, then top with layer 3.
Remove white ruler tab.
Step 5
Cut a hole in drape the approximate size
of a quarter. Remove paper backing 1 from
bottom of the Port Pad. Position Port Pad
opening over the hole that was created.
Remove backing 2 from the top of Port Pad.
Flip handler tabs over on each side and
peel down to remove.
Step 6
Select canister size and attach to the
back of the pump. Connect the port
pad to the canister by securing the
purple luer lock.
Step 7
Initiate therapy by pressing the
universal on/off button
. Adjust
pressure as prescribed using the
up/down arrows.
Step 8
A secure seal is identified when the
foam draws down and the target
pressure is reached.
...................................................................................................................................................................................................................................................................................................
Questions?
Call 877.790.5994 | JMeds.com
©
JMeds 2020
XLR8/XLR8 Plus
Application Guide
Application Guide
XLR8/XLR8 Plus
Questions?
Call 1.800.208.2025 or 516.217.0010 | email [email protected] | www.genadyne.com
©2016 Genadyne Biotechnologies, Inc. CLN-003 02/16
Step 1
Select appropriate size dressing kit for
wound. Kit contains foam, port pad,
and 2 drapes. (Small kit has
1 drape only.)
Step 2
Clean the wound according to protocol.
Protect wound edges with drape.
Step 3
Cut foam to fit accurately in wound
bed. Avoid overlapping onto intact
skin. Avoid cutting foam over wound.
Avoid over-packing, as this will inhibit
filtration of drainage.
Step 4
Cover foam with drape by separating
bottom layers 1 and 2 to expose the
adhesive drape. Position and place
drape over foam. Remove stabilization
layers 1 and 2, then top with layer 3.
Remove white ruler tab.
Step 5
Cut a hole in drape the approximate size
of a quarter. Remove paper backing 1 from
bottom of the Port Pad. Position Port Pad
opening over the hole that was created.
Remove backing 2 from the top of Port Pad.
Flip handler tabs over on each side and
peel down to remove.
Step 6
Select canister size and attach to the
back of the pump. Connect the port
pad to the canister by securing the
purple luer lock.
Step 7
Initiate therapy by pressing the
universal on/off button
. Adjust
pressure as prescribed using the
up/down arrows.
Step 8
A secure seal is identified when the
foam draws down and the target
pressure is reached.
...................................................................................................................................................................................................................................................................................................
