background image

THREE

TEN

1

2

3

4

Assemble cross-members and frame rails as shown and let dry for a 

few minutes. Frame may be painted at this time (see page 10 for color 

detail).  Gently  spread  front  of  frame  rails  and  cement  assembled 

engine  and  engine  crossmember  #60  into  place,  then  cement  in 

assembled radiator. Some manipulation will be necessary to locate the 

fan into the radiator shroud, work while the glue joints are still flexible.

VERY IMPORTANT:

Scrape paint and chrome plating
off of areas to be joined by cement.

Engine - I-H V-800 turbo-charged.

Assemble engine block halves; attach parts

as shown. Cement non-plated parts first.

Glue 

radiator assembly

 parts together.

NOTE:

 

Engine may be 

painted a Medium

Metallic Blue.

Detail Pulleys Flat

Black

. Paint

Transmission

Black

101CR

130

154

129

147

146

152

145

153

138

125

10

11 

131

13

8

9

64

61

62

65

41

39

40

66

137

167

158

161

162

139

160

63

49 (R)

78 (L)

12

60

60

33

84CR (2)

S-CL (2)

Paint Amber

115CR

4-CL (2)

106CR

80CR (4)

77CR (2)

93CR

Be sure to use only paint formulated for use on styrene plastic. 

Liquid cement may be applied with a fine 00 brush for neat glue 

joints.  Also,  the  new  "instant"  glues  may  be  used  for  small 

non-chrome  —  caution  must  be  used  when  working  with  this 

cement  as  it  WILL  cement  fingers  together  as  well  as  anything 

else. Do not use on clear parts as hazing may occur.

If  cement  gets  on  an  outside  surface,  use  600  grit  wet-or-dry 

emery paper to sand it smooth. Then press out some toothpaste 

and apply it with a cotton swab, rubbing in a circular motion. 

This  will  polish  out  the  cement  blemish.  DON'T  PRESS  TOO 

HARD! This also works on clear parts.

It is a good idea to wash plastic parts in mild detergent before 

painting to remove all oils from your hands . . . the paint will go 

on smoother and easier. Sand parts lightly before painting.

The color of the frame for the version of the Eagle duplicated in 

this kit is a dark green. The V-800 engine is a metallic blue - the 

transmission  matches  the  frame.  The  interior  of  all  Eagles  is  a 

maroon  color;  the  instrument  panel  is  maroon  with  flat  black 

around  the  instruments.  The  steering  wheel  is  black  with  silver 

spokes.

MODELING AND PAINTING TIPS:

Содержание Transtar 4300 Eagle







Отзывы: