AMT A200-90 Скачать руководство пользователя страница 1

Specifications Information and Repair Parts Manual  

     

A200-90

A200-250-00

1

8/2013

Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate 

or maintain the product described. Protect yourself and others by observing all safety information. The Safety Instructions are contained in the General Operating 

Instructions. Failure to comply with the safety instructions accompanying this product could result in personal injury and/or property damage! Retain instructions 

for future reference.  AMT reserves the right to discontinue any model or change specifications at any time without incurring any obligation.

©2013 American Machine & Tool Co., Inc. of PA, A Subsidiary of The Gorman-Rupp Company, All Rights Reserved.

Periodic maintenance and inspection is required on all pumps to ensure proper operation. Unit must be clear of debris and sediment. Inspect for leaks and loose bolts. Failure to do so 

voids warranty.

Mounting Frame

SPECIFICATIONS

Material: Steel Plate

Finish: Paint or powder coated finish, color: black

Weight: 44 lb. [20 kg]

Overall dimensions (max):  

30” [762mm] long 

   14.2”[ 

360mm] 

wide 

   5.1” 

[130mm] 

tall

GENERAL

Mounting frame is designed to support a pump end and driver while also 
providing a convenient way to secure the entire assembly to a suitable 
grounding base plane.

GROUNDING BASE PLANE

Mounting frame must be secured to a grounding base plane. Grounding 

plane  must  be  flat,  level,  and  of  sufficient  strength  and  size  to  support  the 

entire frame/driver/pump assembly along with any loads the piping system 
generates. Frame is designed to provide a convenient form of mounting the 
driver/pump. It is not designed to handle excessive piping system loads or 
provide total support in and of itself. Frame is designed to transfer the loads 

to a flat grounding base plane that supports the entire frame. If frame is not 

supported correctly, damage to frame and pump assembly may occur.

FRAME MOUNTING FASTENER LAYOUT

 

Refer to Figure 1

Frame  mounting  holes  are  sized  to  accommodate  3/8”  [10  mm]  diameter 

fasteners. Ref. Drawing 1 is provided for fastener spacing and layout. Due 
to dimensional tolerances and assembly variations, it is best to measure your 
actual unit to determine the exact fastener spacing before installation.

VIBRATION

Mounting frame can be fastened directly to the grounding plane, but if unit 
vibration is excessive during operation, pump damage may occur. Some form 
of vibration dampening mount between pump/frame assembly and grounding 
plane should be considered.

PUMP/DRIVER TO FRAME MOUNTING 

Refer to Figure 2

If A200-90 mounting frame is purchased as an accessory to be mounted to a 

pump in the field, follow the following instructions:
• 

Measure vertical distance from pump end support foot or casing bottom to 
motor mounting foot.

• 

If distance is 0 to 1.3”, fasten motor to frame “driver mount” with bolts, nuts 
and washers provided.

• 

If  distance  is  1.3”  to  2”,  the  driver  support  must  first  be  repositioned. 

Remove four M12 bolts holding driver mount to mounting rails. Move 
driver mount up and install M12 bolts into lower set of holes in driver 
mount. Realign frame cross members. Torque bolts to 35 ft-lb [47 N-m]. 
Fasten motor to driver mount with bolts, nuts and washers provided.

• 

If distance is greater than 2.1”, motor must be spaced above driver mount 
as needed. This will require longer bolts than supplied. Adding spacers will 
void any warranty.

• 

Loosen four M12 bolts securing pump support to mounting rails. Slide 
pump support up until it supports the pump foot or casing bottom. If pump 
foot has provisions for mounting bolts, holes must be drilled into the pump 
support at the appropriate locations. Secure pump foot with appropriate 
fasteners (not provided).

REPAIR/REPLACEMENT PARTS

Mounting frame is available as a complete unit only. Replace entire unit if 
damage occurs.

DESCRIPTION

Mounting frame for 145/182/184/213/215JM motor driven pumps.

Отзывы: