AMT 3880-97, Спецификация, информация и руководство по ремонту запасных частей

Страница: 2 / 4

3880-252-00 2 09/2011
Specifications Information and Repair Parts Manual
3880-97 thru 3884-97
x
Swimming Pool/Hot Tub Pumps
Repair Parts List
Ref. Part Number for Models:
No. Description 3880-97 3381-97 3882-97 3883-97 3884-97 Qty.
1 Motor 1626-009-00 1626-010-00 1626-011-00 1626-012-00 1626-024-00 1
2 Slinger Washer (optional, not required) * * * * * 1
3 Fastener * * * * * 4
4 Adapter 4294-030-09 4294-030-09 4294-030-09 4294-030-09 4294-030-09 1
5 Fastener * * * * * 6
6 Fastener * * * * * 4
7 Casing Cover 2104-003-01 2104-003-01 2104-003-01 2104-003-01 2104-003-01 1
8 Casing Seal -Buna N (standard) 2104-004-00 2104-004-00 2104-004-00 2104-004-00 2104-004-00 1
-Viton (optional) 2150-023-00 2150-023-00 2150-023-00 2150-023-00 2150-023-00
9 & 10

Shaft Seal Assembly -Buna N (standard) 1640-161-90 1640-161-90 1640-161-90 1640-161-90 1640-161-90 1
-Viton (optional) 1640-161-91 1640-161-91 1640-161-91 1640-161-91 1640-161-91
11 Impeller Shim Package 1657-000-90 1657-000-90 1657-000-90 1657-000-90 1657-000-90 1
12 Impeller 3880-050-01 3880-050-02 3880-051-01 3880-052-01 3880-052-02 1
13 Casing 2104-000-01 2104-000-01 2104-000-01 2104-000-01 2104-000-01 1
14 Pipe Plug * * * * * 1
(*) Standard Hardware Item, Available Locally
(

) Seal assembly available as set only (includes seal head and seat).
SHIM ADJUSTMENT
When installing a replacement impeller (Ref. No. 12), motor (Ref. No. 1), casing
(Ref. No. 13), casing cover (Ref. No. 7), or adapter (Ref. No. 4) it may be
necessary to vary number of shims (Ref. No. 11) to ensure proper running
clearance between impeller and casing. Proceed as follows:
NOTE:
A g 6”
1.
, ”
additional to those removed originally.
2.
, ”
removed during disassembly.
3. Disassemble and reassemble pump as described for component being
replaced in applicable steps under MECHINCAL SEAL
REPLACEMENT.
IMPORTANT: Ensure that casing is snugly in place and check shaft to make
g y 7/ 6” wrench on end of
motor shaft to turn). If it turns freely, check to ensure that casing cover and
g “ ” “
” y I y , g R N 5
and 6) and recheck shaft for free turning. Tighten carefully, turning
shaft while
tightening so that motor bearings are not damaged in the event that too many
shims were installed. If shaft seizes before fasteners are completely tight,
disassemble pump and remove one shim and repeat reassembly.
For Repair Parts contact dealer where pump was purchased.
Please provide following information:
-Model Number
-Serial Number (if any)
Part description and number as shown in parts list
Figure 2
– Repair Parts Illustration