SEALANT
AREA
NO SEALANT
ON FIRST 1-2 THREADS
8
9
3
12
13
11
14
1
*
EaBP-90
9
9
EaBP-100
10
1
⁄
2
9
EaBP-110
13
1
⁄
2
9
3
15
⁄
16
9
3
3
⁄
16
9
IN
IN
OU
T
OUT
Diagram B
MINIMUM AREA
NEEDED FOR
MOUNT AND OIL
FILTER ELEMENT
* Mount and element
heights plus 1-inch
removal clearance
Mounting Angle Diagram A
(Recommendations are the same right to left and front to back)
Mounting angle above horizontal is not recommended
Diagram C
Note:
If Teflon tape is used, it should be
wrapped no more than 1
1
⁄
2
to 2 turns in a
clockwise direction when viewed from the
thread end.
Caution:
More than two turns of tape may
cause distortion or cracking of the port. Never
back off (loosen) pipe threaded connectors to
achieve alignment.
1
1
⁄
16
9
49
⁄
64
9
(1.066)
(.765)
1
1
⁄
16
9
(1.066)
(.3125)
5
⁄
16
9
fitting swivel nut to 130-150 inch pounds or from finger tight, rotate an additional 120° or
1
⁄
3
of
a turn. See diagrams D and H for additional details.
8. Use plastic ties (BP-46) to secure hoses in position and away from damage. Trim ties, using side cutter.
N
No
otte
e::
Over tightening the plastic ties may cause the hose to collapse and restrict oil flow.
F. Start up procedures
1. Check that all fittings and hoses are securely attached, and that the hoses are routed properly.
2. Check engine oil level. Fill to full mark if necessary.
3. Set vehicle parking brake. With transmission in park/neutral start the engine and immediately check
oil pressure.
N
No
otte
e::
Pressure may initially take a moment or two to rise.
C
Ca
au
uttiio
on
n::
Carefully check for leaks at fittings, hoses and mount. If leaks are observed,
S
ST
TO
OP
P
E
EN
NG
GIIN
NE
E IIM
MM
ME
ED
DIIA
AT
TE
EL
LY
Y,,
repair leaks and continue.
4. After engine has warmed, shut off and re-check engine oil level. Fill as necessary.
5. Record vehicle mileage/operating hours and date of installation.
G. Periodic maintenance
1. Periodic visual inspection of the fittings and hoses is recommended. Check for leaks, hose dete-
rioration and cuts. Repair and/or replace as necessary.
2. Refer to Recommended Filter Change Interval chart for servicing intervals.
3. To change the filter element:
a. Ensure engine is off and use caution as the engine, oil and filter may be hot and could result
in an injury.
b. Using a filter wrench, remove the filter element. Dispose of properly.
c. Clean the filter gasket contact area on the mount with a clean, lint-free rag.
d. Lubricate the new filter gasket with clean oil.
e. Fill filter as full as possible with engine oil.
f. Screw on new filter, tighten per instructions on the filter.
g. Start engine and check for leaks.
h. Check engine oil level, fill as needed.
i. Record vehicle mileage/operating hours for future reference.
GOOD
ANGLE
ACCEPTABLE
ACC EP
TABLE
GOOD
ANGLE
PREFERRED MOUNTING ANGLE
HORIZONTAL
0°
20°
50°
130°
160°
180°
Parts and assembly list
Single Mount By-Pass Filter System (BMK-21)
Item
Description
Qty.
Part No.
1.
Oil Pressure Sending Unit (existing)
2.
Filter Mount Assembly, Spin-On
1
BK-303
3.
Fitting Adapter
4
BP-208
4.
5
⁄
16
9
Fender Washer
3
BP-205
5.
5
⁄
16
9
Flat Washer
3
BP-120
6.
5
⁄
16
9
-18 Self Locking Nut
3
BP-121
7.
5
⁄
16
9
- 18 x 1
9
Hex Head Bolt
3
BP-122
8.
1
⁄
4
9
I.D. Hose
8
8
BP-251
9.
Hose Fitting
4
BP-261
10.
Street “T” (
1
⁄
8
9
x
1
⁄
8
9
x
1
⁄
8
9
)
1
BP-33
11.
Straight “T” (
1
⁄
4
9
x
1
⁄
4
9
x
1
⁄
4
9
)
1
BP-34
12.
90° Street Elbow,
1
⁄
8
9
4
BP-52
13.
Bushing
1
⁄
8
9
x
1
⁄
4
9
1
BP-38
14.
Nipple
1
⁄
4
9
x 2
9
1
BP-39
15.
Self Tapping Hollow Bolt
1
BP-40
16.
Sealing Gasket
1
BP-41
Plastic Tie
2
BP-46
Thread Sealant
1
BP-198
Instruction Sheet
1
BP-83
Optional parts available from AMSOIL INC.
Filter Cap for 6.0L Ford
BK-1101
Oil Fill Cap for 6.0L Ford
BK-1102
Oil Filter Sandwich Adapter for GM Duramax
BK-1201
Oil Fill Cap for GM Duramax
BK-1202
Oil Fill Cap for Dodge Cummins
BK-1301
Fitting Adapter
1
⁄
8
9
NPT –
1
⁄
4
9
JIC (stainless)
BP-241
90° Elbow
1
⁄
8
9
NPT –
1
⁄
4
9
JIC
BP-242
Oil Sampling Kit
BP-67
Oil Return Swivel Fitting
BP-89
Deluxe Oil Sampling Valve
1
⁄
4
9
NPT
G-1570
Mounting Template
Diagram D
Minimum Bend Radius
(Actual size)
3
⁄
4
9
(.75)
1
⁄
4
9
I.D. Hose BP-251
Optional installation
at Oil Sending
Location (for
1
⁄
4
9
)
Diagram G
Содержание BMK-21
Страница 6: ......
