background image

 

Two Post Car Lift AM-TPL12CF 

 

 

 

IMPORTANT INFORMATION 

 

 

 

The shipment should be thoroughly inspected as soon as it is received. Any freight 
damage or missing items must be noted on the freight bill before signing and reported 
to the freight carrier with a freight claim established.  The buyer should claim 

compensation from the freight carrier if any damage happens to the equipment during 
shipping. Please refer to our website for detailed shipping policies and procedures. 

 

Make sure you have additional help or heavy-duty lifting equipment when unloading and 
assembling the lift. 

 

Read and understand this installation and operation manual entirely before attempting 
to install or operate the lift. 

 

Keep this manual near the product for future references. 

Make sure all operators read this manual. 

 

The lift should only be operated by authorized personnel. Keep children and untrained 
personnel away from the lift.  

 

Do not make any modifications to the Lift; this voids the warranty and increases the 

chances of injury or property damage. •

 

 

Do not use the lift while tired or under the influence of drugs, alcohol, or medication 

 

The manufacturer or distributor assumes no responsibility for loss or damage of any 
kind, expressed or implied, resulting from improper installation or use of this lift. Always 
use professional installation companies. 

 

All persons using the equipment must be responsible, qualified, and carefully follow the 
operation and safety guidelines contained in this manual. 

 

A level floor is required for proper lift installation and operation. 

 

DO NOT install this lift on any asphalt surface. Lift must be installed on the concrete 
surface a minimum of 12

” thick and 3,

000 psi tensile strength with steel or fiber mesh. 

Reinforcement. New concrete must be adequately cured by at least 28 days minimum. 

 

DO NOT install this lift over concrete expansion joints or cracks. (Consult with your 
building engineer) 

 

DO NOT install this lift on the upper floor without written authorization from your 
building engineer. Should only be installed on the ground floor without a basement. 

 

DO NOT attempt to lift only part of a vehicle. This lift is intended to raise the entire body 
of a vehicle only. This will bend the arms and void the warranty. 

 

NEVER lift any persons or vehicles containing persons. This lift is designed to lift empty 
vehicles only. 

 

Any vehicle whose weight is above 12,000lb is not allowed to be raised on this machine. 

 

All wiring must be performed by a licensed, certified Electrician.  

 

Do not perform any maintenance until the main electrical power has been disconnected 
from the lift and cannot be re-energized until all procedures are complete. 

 

All information in this manual is believed to be correct at the time of publication. The 
design, material, and specifications are subject to change without notice. 

 
 
 
 
 
 
 
 
 
 
 

Содержание AM-TPL12CF





























Отзывы: