manualshive.com logo in svg

Amrel PPS-1322/1302A, Руководство пользователя

Поделиться
Скачать
Amrel PPS-1322/1302A Скачать руководство пользователя страница 31

31 

[default]), and the power supply address is 12 as is the case for all models. Then the communication path for this 
combination is 512. 
 
COMMON COMMANDS: There is a wide variety of commands available to program the power supply. However, 
the commands which pertain to voltage and current are of most use. These commands are: VSET, ISET, OVSET, 
VOUT?, IOUT?, OVSET? and OCP. 
 
Secondary commands of prime importance pertain to the actual programming language. Some of these commands 
are: OUTPUT, ENTER, DELAY, SEND, PRINT, and CLEAR. The definitions and uses of these commands are as 
follows: 
 
OUTPUT: Addresses the power supply to listen and sends command to power supply. 
 
ENTER: Addresses the power supply to talk and receive data from the power supply. 
 
DELAY: Introduces a time delay to the power supply. 
 
 note: This command is extremely important since the power supplies occasionally require time delays 

in order to execute operations. Otherwise, error messages occur. 

 
CLEAR: Clears the power supply. 
 
 note: The PPS series does not have a CLR command. Therefore, the user must initially specify a 

hardware clear before beginning programming. 

 
SEND:  Sends GPIB management commands. 
 
PRINT:  Prints the specified data to screen or printer. 
 
RUN:  Executes the program.  
 
All commands may be accepted in either upper or lower case letters in ASCII code. The PPS Series accepts integer 
or numeric data as input. Plus (+) and minus (-) signs are also numeric characters. Remember not to program too 
large a value since the power supply rounds off data to suit the power supplies resolution.  
 

SENDING DATA: 

The steps involved in sending data to the power supply are setting the address (power supply & 

computer), function and sending the command (basic). For example, to turn on the output of a power supply 
(single output), send: 
 
 

OUTPUT 512; OUT 1 

where:  
 OUTPUT - Basic Statement 
 512 - DMA channel (5) and GPIB device address (12) 
 OUT - GPIB command 
 1 - enable output (0 disable output) 
 
Continuing on with this example we will set  the output voltage to 11V and output current to 1.7 amps, therefore 
send: 
 

OUTPUT 512; VSET 11 

      OUTPUT 512; ISET 1.7 

 NOTE: The voltage and current values are given in volts and amps. 

Содержание PPS-1322/1302A













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды