manualshive.com logo in svg

Ampro Stylist, Инструкция по эксплуатации

Поделиться
Скачать
Ampro Stylist Скачать руководство пользователя страница 20

20 

 

 

FULLY GUARANTEED 

 
 
An Ampro Precision Projectors bear an unqualified 
guarantee as to original defects in materials or 
workmanship. 
 
Any part or parts showing such defects will be 
promptly replaced without charge, provided projector is 
returned to factory transportation charges prepaid. 
 
Our guarantee does not cover projection lamps, which 
are covered by the lamp manufacturers. If the rated life 
of projection lamp is not obtained, return lamp to dealer 
or to factory and lamp Will be submitted to lamp 
manufacturer for adjustment. 
 
An addressed registration card is furnished with each 
projector shipped from factory. This card should be 
filled in and mailed promptly after machine is 
purchased to obtain full benefits of guarantee, and aid 
in recovery of projector if lost or stolen. 
 
It is understood that the replacement of parts damaged 
as a result of natural wear, the adding of attachments 
not supplied by Ampro Corporation. abuse or 
tampering, is not covered by this guarantee. 
 

 

 

 
 
 
 
 
 

A-472-5-51 

 

 

 

 

 

 

PRINTED IN U.S.A. 

Содержание Stylist





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды