3
•
Select a channel (1
-
16) on side panel
(I)
of bodypack using the
supplied screw driver to select channel number.
Channel select-
ed should match channel on receiver
. When transmitter and
receiver are set to correct channel the
RF
INDICATOR
(B)
will glow
red when transmitter is turned on.
•
Plug the Lapel / Headset microphone into the
MIC
INPUT
JACK
(K).
The lapel microphone can be clipped to a necktie or other cloth-
ing, using the supplied clip. The lapel mic should be placed under
the chin, as close to the center of the body as possible.
•
Slide the power
ON
/
OFF
switch
(J)
to the
ON
position, the
LED
INDICATOR
LIGHT
(L)
will illuminate green. Replace batteries when
this LED turns red.
●
MUTE
LEVEL
ON
RECEIVER
(F)
is set at half way mark when it leaves
the factory. If speaker sound is breaking up, turn level clockwise
with small screwdriver until condition improves.
•
MIC 1
:
Adjusts volume level of gooseneck microphone on
reading table.
•
MIC 2:
Adjusts volume level of microphone plugged into the
MIC 2 input jack on amplifier.
•
AUX:
Controls output level of device that is plugged into the
L/R RCA jacks.
•
BASS:
This control cuts or boosts the bass level.
•
TREBLE:
This control cuts or boosts the treble level.
J
I
K
H
•
The receiver has its own
POWER
/
VOLUME
control
(G).
Turn
Power On. A Frequency Channel will appear in the Channel
Display
(A).
Press Select Buttons (
E
) to select a channel. Chan-
nel number must match channel number on wireless transmitter.
•
The
TRANSMITTER
BODYPACK
is operated by 1
-
"AA" 1.5 Volt
alkaline battery. Slide off battery cover
(H)
and install battery as
shown. Make certain the battery is fully seated in its compart-
ment so the cover slides in place easily. Battery life with alkaline
batteries is approximately 8 hours of operating time.
CONTROL PANEL
Y
OUR
LECTERN
MAY
NOT
CONTAIN
ALL
OF
THE
ELECTRONIC
MODULES
AS
SHOWN
AND
EXPLAINED
HERE
.
A
B
C
G
F
E
D
Battery Cover
Channel Selector
Top Panel
L
BATTERIES
Install batteries as follows;
•
Hold the body of microphone
in hand and twist off bottom
section of microphone.
•
Insert two “AA” 1.5 V batteries.
•
Twist bottom section back on to
microphone.
BATTERY STATUS
The life expectancy of the two batteries is about 10 hours. When the
“BATTERY”
symbol
on the display screen keeps flashing the batteries
should be replaced immediately.
AUTO SYNC
TO
RECEIVER
First select channel you wish to use on the receiv-
er. Then press the ASC button (
D
), the IR light will
start to flash. Turn on microphone and point end
(
M
) of microphone at the flashing IR light on re-
ceiver and the microphone will auto sync to the
same channel as selected on the receiver.
M
Functions
1)
Interchangeable Microphone Head
2)
LCD Screen
3)
Power / Mute Control Switch
4)
Select Button
5)
5)
Microphone Input Sensitivity Adjust-
ment
—is used to set the gain of microphone.
If you are a soft talking speaker you will need
to turn the control counter clockwise. Turn
clockwise if you are a loud talker. Use plastic
screwdriver that is supplied.
C
ONTINUED
NEXT
PAGE
16 CHANNEL WIRELESS RECEIVER
RECEIVER / TRANSMITTER (BODYPACK) SETUP
WIRELESS HANDHELD MICROPHONE—MODEL S1695
•
Channel Display (A)
•
RF
-
Radio Frequency Indicator (B)
•
AF
-
Audio Frequency Indicator (C)
•
ASC / IR Auto Channel Select (Handheld Only) (D)
•
Select Buttons
-
Manual Channel Selection (E)
•
Mute Level Adjustment (F)
•
Volume Control (G)
