Troubleshooting Tips
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
I entered setup.ampedwireless.com and it failed to open the Web Menu.
a. Make sure your computer is connected to the Router using the included Ethernet cable.
Ensure that the power on the Router is on.
b. Check that your computer IS NOT connected to any wireless networks. If it is, disable your Wi-Fi connection
and disconnect from all wireless networks. Reboot the Router and try again.
c. Close your current web browser and reopen it. Use Google Chrome, Internet Explorer (8.0 and up), or Safari.
d. Open your web browser and enter 192.168.3.1 into the web address bar.
e. Reset the Router to default settings by holding the Reset button (located on the back panel) for ten (10) seconds
and try again. The Setup Wizard should appear. To access the Dashboard, complete or skip the Setup Wizard.
The Setup Wizard appears only when the Router has not yet been configured.
f. If you still cannot access the menu, disconnect the Ethernet cable and connect wirelessly to the Router. Open
your web browser to setup.ampedwireless.com.
g. If the Setup Wizard appears instead of the Dashboard, the Router has not yet been configured. Complete the
Setup Wizard or skip the Setup Wizard to access the Dashboard.
The Setup Wizard could not automatically configure my Internet connection.
a. Reset your modem by holding down the Reset button located on the back of the modem for approximately
ten (10) seconds. Try again.
b. Reboot the Router by unplugging the power adapter and plugging it back in.
c. Static IP: Your Internet connection may require a static IP setting. Check with your ISP to obtain the IP settings.
d. DSL Connection: Your Internet connection may require login information. If you are using PPPoE mode,
you will need to manually configure your Internet connection settings and obtain your username and password.
e. Cable Modem: Your Internet connection may require you to clone your MAC address. Go to More Settings >
IP Settings > Internet Network (WAN) and select Automatic/Dynamic (DHCP) from the dropdown menu.
Clone your PC’s MAC address under the DNS settings.
Amped Wireless
A Division of Newo Corporation
Copyright © 2017 Amped Wireless / Newo Corporation. All rights reserved.
Amped Wireless, Newo Corporation, the Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.
If you continue to have issues setting up the Router, give us a call — we’re here to help: 888-573-8820 or 909-217-3168
Visit our website for more support information and answers to frequently asked questions: www.ampedwireless.com/support
v061217
Using the Features on the Router
The Router is equipped with many powerful security features which can be accessed through the web
menu on the left side under
Smart Features, Firewall Settings
and
Quality of Service
:
If you are unfamiliar or want more information on how to set up Smart Features, Firewall Settings, or Quality
of Service, please refer to the User’s Guide at http://support.ampedwireless.com/b1900rt
12:26
Wireless Access Scheduling
Control when your Wi-Fi is on/off
Location: 2.4 or 5GHz Wi-Fi Settings > Access Schedule
User Access Control
(MAC/IP)
Restrict network access to specific users
Location: Smart Features > User Access
Wireless Coverage Control
Adjust the distance of your wireless network
Location: 2.4 or 5GHz Wi-Fi Settings > Wireless Coverage
Block Websites
Prevent access to specific websites
Location: Smart Features > Block Websites
Firewall Settings
Protect your network from outside intruders
Location: Firewall Settings
Quality of Service (Prioritize Bandwidth)
Manage your network bandwidth
Location: Quality of Service
www
www
Web Menu (Left Side)
LED Lights On/Off
•
Push button to turn the LED indicators on the front of the Router on or off.
Additional Router Features
Reset the Router to Default Settings
There are two options to reset the Router back to factory default settings:
Reset
Button
a
Wired Ports
b
c
LED Lights On/Off
1
2
Access the Reset button through the web menu on the left side under
More Settings > Management > Save/Reload Settings
. Select the
Reset
Settings to Default
.
Access the physical Reset button on the back panel of the Router:
Hold down the Reset button for five to ten (5-10) seconds. You may
need to use a pen tip or pin to access the button. Pressing the Reset
Button for less than five (5) seconds will simply reboot the Router while
saving your existing settings.
a
b
Wired Port LEDs
•
Indicates when a device is connected to a wired port (modem or local
network) on the back of the Router. The LED will light up when wired
data traffic is transmitted or received. The green LEDs display
when there is an active gigabit connection.
c
Wi-Fi Protected Setup (One-Touch Setup or Push Button Configuration)
If your Wi-Fi device has WPS one-touch setup, you can use it to connect to the Router:
iPad Tablet
Tap the "Home" button to get to the home page.
Tap the "Settings" app icon.
Tap on Wi-Fi to enter the iPad’s Wi-Fi settings.
Toggle the Wi-Fi "On/Off" selector switch to "On".
Under "Choose a Network," select:
Amped_B1900RT_5.0
or
Amped_B1900RT_2.4
Amped_B1900RT...
Amped_B1900RT...
Tap the "Apps" menu on the tablet screen.
Locate and tap the "Settings" app icon.
Under "Wireless & networks," tap "Wi-Fi settings".
Tap the Wi-Fi box to turn on Wi-Fi and scan.
Under "Wi-Fi networks," select:
Amped_B1900RT_5.0
or
Amped_B1900RT_2.4
A.
B.
C.
D.
E .
A.
B.
C.
D.
E.
Android Tablet
Mac OS X
Click on the Wireless icon to see available wireless
networks. Select
Amped_B1900RT_5.0
or
Amped_B1900RT_2.4
.
Access the taskbar on the bottom right of your
screen, tap on the Wi-Fi icon, enable Wi-Fi, and select
Amped_B1900RT_5.0
or
Amped_B1900RT_2.4
.
Windows 10
How to Connect Wirelessly to the Router
Tap on your Settings icon, select Wi-Fi, and
choose the network,
Amped_B1900RT_5.0
or
Amped_B1900RT_2.4
.
Amped_B1900RT...
Amped_B1900RT...
Amped_B1900...
iPhone
Swipe in from the right edge to access the charms
bar, tap on Settings, select the Wi-Fi icon, and select
Amped_B1900RT_5.0
or
Amped_B1900RT_2.4
.
Amped_B1900RT...
Network01
Network02
Windows 8
Hold down the WPS button on the Router (back panel) for 3 seconds. The Power LED will begin to blink.
As it blinks, push the WPS button on your wireless adapter or enable WPS with the provided software for your
wireless adapter. WPS will automatically configure the connection settings for your wireless adapter to connect
to the Router.
A.
B.
Indicates when the Router is powered on. The LED will remain on.
Blinks when Wi-Fi Protected Setup (WPS) is activated and the Router awaits a connection.
Indicates when the Router is connected to a broadband modem.
The LED will light up when Internet traffic is transmitted or received.
The LED will light up when data traffic is transmitted or received over the 5GHz wireless
network.
The LED will light up when data traffic is transmitted or received over the 2.4GHz wireless
network.
The LED will light up when data is being transmitted or received through the wired ports.
Power:
WPS:
Internet Connection:
5GHz Wireless Activity:
2.4GHz Wireless Activity:
Wired Port Activity:
LED Indicator Information
This is the second page of the Setup Guide. Start on the opposite side first.