manualshive.com logo in svg

AMOT 2230C, Инструкция по установке, эксплуатации и обслуживанию, Страница: 19 / 20

Поделиться
Скачать
AMOT 2230C Скачать руководство пользователя страница 19

19 

Technical Data

 

OMM223000015 

Rev 2 – May 06  

Section 6 

Technical Data 

 

Construction  

 

2230

 

4430

 

Body and nut 

Brass 

316 SS 

Seals Viton Viton 
Element Brass  Brass 
Extensions Brass 

316 

SS 

Weight 

Max net weight  
(2230 and 4430) 

0.57 kg (1 – 1/4 lb) 

Max net weight 
(Well) 

0.45 kg (1 lb) 

Pressure 

Inlet pressure 

8.62 bar (125 psi) maximum 

Sensed pressure with well fitted: 
2766L 

690 bar (10000 psi) maximum 

3802L 

345 bar (5000 psi) maximum  

Sensed pressure 
Temp element 

55.17 bar (800 psi) maximum 

 

Temperature 

Maximum allowable continuous temperature depends on the Model 
Code: 
Model Code 

Without well 

With well 

A/K 

48.9° C (120° F) 

54.4° C (130° F) 

B/M 

68.3° C (155° F)  

73.9° C (165° F) 

C/N 

85° C (185° F)  

90.6° C (195° F) 

D/P 

101.7° C (215° F)  

107.2° C (225° F) 

E/R 

110° C (230° F)  

115.6° C (240° F) 

F/S 

118.3° C (245° F)  

123.9° C (255° F) 

G/T 

123.9° C (255° F)  

129.4° C (265° F) 

H/W 

135° C (275° F)  

140.6° C (285° F) 

 

Содержание 2230C





















Отзывы:

Нет отзывов