background image

©Copyright AMKUS Rescue Systems 2020-2021

17

LAP-012 October 7, 2021 Rev02

9.0 OPERATION
9.1 GENERAL

The  240SS  is  a  simultaneous  operation  power  unit.  Two  tools  can  be  connected  to  a  single  power  unit  and  operated  either

independently or simultaneously. To operate the 240SS. Ensure there is power to the unit. Begin operation by pressing the system start

button. Then, press the motor button to begin building pressure. Once pressure builds, press the corresponding valve button to charge

the rescue tool for operation.
After completing operations, pressing the green start button turns the entire system off.

9.2 OPTIONAL WIRELESS REMOTE CONTROL
9.2.1 FEATURES

1.

Emergency Stop (Red)

 - Closes both valves and powers down both motors. Press to active Emergency Stop. Rotate thumb

wheel clockwise to resume normal operation.

2.

Start Buttons (Green)

 - Synchronizes the remote to the receiver and activates the system.

3.

M1 Motor Switch (Blue left side)

 - Depress to activate motor for M1 circuit. Depress again to turn motor off.

4.

M2 Motor Switch (Red left side)

 - Press to activate motor for M2 circuit. Press again to turn motor off.

5.

V1 Valve 1 Switch (Blue right side)

 - Press to activate control valve for V1 circuit. Press again to turn control valve off.

6.

V2 Valve 2 Switch (Blue right side)

 - Press to activate control valve for V2 circuit. Press again to turn control valve off.

9.2.2 OPERATING INSTRUCTIONS

1. Rotate  the  Emergency  Stop  (1)  (Red)  thumb  wheel  clockwise  and

release to ensure the remote is in the operation mode.

2. Press and hold both start buttons at the bottom of the remote. While

holding  the  start  buttons  the  remote  is  linking  up  to  the  receiver

mounted  in  the  apparatus.  Hold  the  start  buttons  pressed  firmly  to

ensure a good signal.

3. Push the M1 and/or M2 motor buttons (The motors are programmed

to reach full operating speed in 5 seconds).

4. Push the V1 and/or V2 valve button(s) to activate the appropriate reel

circuits.

5. To shut off a circuit, push the appropriate valve (5) and/or (6) button.

To quickly shut down the entire system including the power, motors and reel

circuits, push the Emergency Stop. 
To re-activate the system, repeat these instructions starting at number 1.

10.0 TROUBLESHOOTING GUIDE

Table 10.0

PROBLEM

POSSIBLE REMEDY

Tool lacks power or speed

Check hydraulic fluid level in power unit reservoir.

Fluid leaks at fittings or hoses

Check tightness of hose fittings.

Replace damaged hoses.

Tools do not operate

Check to that the power unit is running.

Check that the line is charged.

Check hydraulic fluid level in power unit reservoir.

System turns on but screen is dark

Change the PLC battery 

(see section 11.4)

NOTICE

Immediately remove malfunctioning or damaged tools from service. Consult your dealer or AMKUS 

Rescue Systems.

ALL SERVICE MUST BE PERFORMED BY QUALIFIED SERVICE TECNICIANS IN OBSERVANCE OF 

SAFETY REGULATIONS. 

1

5

6

2

3

4

Figure 9.2.2

Содержание Super Simo 240SS





















Отзывы: