Amica APM 3011, Руководство по эксплуатации

Страница: 15 / 20

15
DESCRIPTION OF THE APPLIANCE
Name of components (fig. 1)
1. Control panel
2. Filter Assembly
3. Rear case
4. Air outlet
5. Handle
6. Particulate sensor
7. Air inlet
Proper placement (fig. 2).
l
To achieve better purification effects and avoid
metallic shield effect affecting the communica­
tion, please be sure that the air purifier is over
30cm away from shelters like the walls, and
is also over 50cm away from the metal/home
appliance (7).
Control panel (fig. 3)
l
Air quality tips (1).
l
Air quality tips (2).
l
POWER (3).
l
Purifying rate ­ FAN (4).
The FAN mode has four options for adjusting the
fan speed: „Turbo”, „High”, „Mid” and „Low”.
Additional option for FAN mode:
­ possibility to switch on simultaneously: FAN
+ ION
­ possibility to turn on the time function for each
fan speed with the TIMER button: 1H, 2H, 4H,
8H, continuous mode (when the continuous
mode is selected, no LED by the TIMER button is
on). This also applies to simultaneously activated
modes: FAN + ION.
l
Auto Shutdown ­ TIMER (5).
Optional 1h, 2h, 4h and 8h for the auto shutdown.
l
Auto mode ­ AUTO (6).
Assembly procedures (fig. 2)
l
Remove rear case. Grab the buckle and pull
it out, and then remove the rear case (1).
l
Take out the filter assembly. Hold both sides of
the filter assembly with both hands, and take it
out (2).
l
Remove the protective film of the filter assembly
(3).
l
Mount the filter assembly (4).
l
Mount the rear case (5).
l
Plug in the power cord, and the filter starts up
(6).
AUTO mode:
­ the purifier has the so­called „Light detection
function”. The program automatically changes
the mode: from AUTO to SLEEP mode or from
SLEEP to AUTO ­ this only applies when you
select the „AUTO” mode, and also when you
select simultaneously: AUTO + ION.
­ the program automatically adjusts the fan spe­
ed depending on the level of detection of pollu­
tion in the room (on the panel there is an icon
that changes color, informing about the quality
of air pollution: red ­ BAD, orange ­ NORMAL,
green ­ GOOD. The more polluted the air in
the room, the faster the speed fan speed will
be faster (automatic function to adjust the fan
speed to the pollution degree in the room ­ this
only applies to „AUTO” mode).
Additional option for AUTO mode:
­ possibility of simultaneously activating the time
function: 1H, 2H, 4H, 8H, continuous mode ­
using the TIMER button;
­ simultaneous activation: AUTO + ION.
l
Sleep mode ­ SLEEP (7).
SLEEP mode:
­ works continuously, always at the lowest fan spe­
ed: LOW. The program does not adjust the fan
speed to the quality of the pollution in the room.
­ in SLEEP mode, no possibility to change the fan
speed (manual change of the fan speed causes
deactivation of the SLEEP mode)
­ „icon blanking function” ­ if the SLEEP program
is selected, the remaining information / active
icons are blanked ­ only the SLEEP program
icon is on. Touching the button again, no matter
what button, activates the buttons again for
about 5 seconds.
Additional option for SLEEP mode:
­ possibility of switching on the time function:
1H, 2H, 4H, 8H, continuous mode ­ with
the TIMER button
­ possibility of activating simultaneously:
SLEEP + ION.
l
Anion Function Filter resetting ­ ION (8).
When the Clean indicator light is on, and the filter
is replaced, long press „ION” for 3s to reset the
filter.
l
Clean Prompts (9).
l
Child Lock Prompts (10).
l
Child Lock (11).
It prevents unintentional changes to the settings
(locking with the button: FAN + TIMER, unlocking
with the button: FAN + TIMER).