manualshive.com logo in svg

AMI 221R, Руководство оператора

Поделиться
Скачать
AMI 221R Скачать руководство пользователя страница 11

14. 

Remove the approprate 3-terminal green connector that corresponds to your target wiring.

15. 

Make the following electrical connections to the proper positions on a Phoenix connector.

 

– Connect the fused line side of a 90 —240 VAC power source to the H terminal

 

– Connect the neutral from the power source to the N terminal

 

– Connect the shield ground to a good earth ground or equivalent.

16. 

Connect the Phoenix connector to the appropriate Interface Group.

To complete wiring for another connection, repeat Steps 12 & 13 and select a different connection to install the 
Phoenix connector.

1st Interface Group

RS485 Communications

2nd Interface Group

4–20mA Analog Output

3rd Interface Group

Alarm One Relays

4th Interface Group

Alarm Two Relays

INTERFACE GROUP

CONNECTION

LIST OF INTERFACE GROUP & CORRESPONDING CONNECTION

Note:  The RS485 cable, which has a length of ~ 6 ft (1.8 m), must be purchased 
separately from AMI (Part # 3DON01).

10

Содержание 221R



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды