AMG AMG6184-DR-SF Скачать руководство пользователя страница 5

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.

Page 5 of 12

AMG6184-DR-SF Instruction Sheet
D18236-01.doc

Connections

Video Output Connections

No. of channels.................................... 8
Connectors .......................................... 75 ohm BNC Socket.
Output Impedance............................... 75 ohm terminated.
Output Level ........................................ 1 Volt p-p nominal
Frequency Response .......................... 10Hz to 7MHz.

Optical Connections

PRIMARY OPTO OUT

Connector ............................................ LC/PC
Primary Optical Launch Power............ -5dBm
Wavelength.......................................... 1550nm
Secondary Optical Sensitivity.............. -22dBm
Wavelength.......................................... 1310nm

PRIMARY OPTO IN

Connector ............................................ LC/PC
Primary Optical Sensitivity................... -22dBm
Wavelength.......................................... 1550nm
Secondary Optical Launch Power ....... -5dBm
Wavelength.......................................... 1310nm

Power Connection

Connector Type ................................... 2.1mm screw lock long power jack – centre positive
Connector Partno. ............................... Switchcraft S761K, AMG G16125-00
Supply Voltage .................................... 13.5 to 18.0 Volts DC.
Maximum Power ................................. 10 Watts

Data and Audio Channel Connections

DATA CHANNEL A

Data Channel A ................................... 1 channel
Data Connector ................................... RJ45

Channel A Interface

On Board Data Interface – RS232, RS422 or RS485. Selected by slide switch

above RJ45 connector.

RS485 – switch position - high (closest to BNC connections)
RS422 – switch position – middle
RS232 – switch position – low (furthest from BNC connections)

DATA CHANNEL B

Data Channel B ................................... Not Present

Содержание AMG6184-DR-SF













Отзывы: