Installation
Instructions
M 9 6 8 0 3 2 A
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
BIDET FITTING
Roughing-in Dimensions
BIDET OUTLINE
IS SYMBOLIC
FINISHED
FLOOR
FINISHED
WALL
1-1/4 O.D. TAILPIECE
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
DIVERTER AND
VACUUM BREAKER
ASSEMBLY
1-1/4 MAX.
1-3/16 DIA.
(C)
(H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
TRANSFER VALVE (FOR FLUSHING
RIM OR SPRAY)
8 TO 12
2-1/4
DIA.
Turn off hot and cold water
supplies before beginning.
CAUTION
1
DRAIN INSTALLATION
2
SPRAY INSTALLATION
3
BIDET FAUCET INSTALLATION
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and
screw on the ESCUTCHEON (4) until it locks against
the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Replace UPPER GASKET (7). Position the side threaded
outlet rearward and secure MOUNTING NUT (9).
Thread ESCUTCHEON (5) onto TRANSFER VALVE (8)
until it seats against the BIDET LEDGE.
Remove MOUNTING NUT (9) and UPPER GASKET (7)
from TRANSFER VALVE (8) and insert into the center
forward hole of BIDET.
STOPPER
Assemble O-RING (1), WASHER (2), PIVOT ROD (3)
and NUT (4) to DRAIN BODY (5). Concave side
of cup WASHER (2) is toward ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
Assemble SPRAY BODY (1) to BIDET.
Using putty, seal underside of SPRAY
BODY FLANGE (2) and secure with
NUT (3).
Screw SPRAY CAP (8) onto SPRAY BODY (1).
Screw SPRAY HOSE (4) with SEAL
WASHER (5) to SPRAY BODY (1).
Connect other end of HOSE (4) with
SEAL WASHER (5) to side outlet
NIPPLE (6) of the TRANSFER VALVE (7).
BIDET
PUTTY
CLIP
PUTTY
COLD
HOT
BIDET
LEDGE
3
4
9
3
1
4
11
6
5
8
7
2
2
7
8
1
9
5
5
2
7
6
7
1
3
5
4
8
10
DO NOT: CLEAN THE PRODUCT WITH SOAPS,
ACID, POLISH, ABRASIVES, HARSH CLEANERS,
OR A CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN
WITH CLEAR WATER. DRY WITH A SOFT
COTTON FLANNEL CLOTH.
DOUCHE SPRAY
2-1/8
DIA.
7391.229
7391.224
T M
Williamsburg
