ONE SHOWER SYSTEM
Installation
Instructions
Certified to comply with ANSI A112.18.1
2064.724
2
Recommended Tools & Materials
ROUGHING-IN DIMENSIONS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Electric Drill
10mm (3/8)
Drill Bit
Pencil
Phillips Screwdriver
76mm
(3)
FINISHED WALL
95mm
(3-3/4)
54mm
(2-1/8)
38mm
(1-1/2)
19mm
(3/4)
33.5mm
(1-3/16D.)
96mm
(3-3/4)
41mm
(1-5/8)
586-595mm
(23-1/8, 23/3/8)
591mm
(23-1/4)
591mm
(23-1/4)
591mm
(23-1/4)
620mm
(24-3/8)
FINISHED FLOOR
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
915mm
(36)
1219mm
(48)
TO
Hammer
MODEL NUMBER
ONE
SHOWER BAR
CARE INSTRUCTIONS:
DO:
SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT:
DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
32mm
(1-1/4)
13mm
(1/2)
1/2" NPT
RUBBER GASKET
FINISHED
WALL
1/2" NPSM HOSE
CONNECTION
53mm
(2-1/16)
60mm
(2-3/8")
25mm
(1")
1/2" NPSM
151mm
(6")
203mm
(8")
65mm
(2-1/2")
(48" - 60") (OPTIONAL)
TO FINISHED FLOOR
59"
Teflon Tape
Level
1
Turn off hot and cold water
supplies before beginning.
CAUTION
INSTALL WALL SUPPLY
1/2" NPT
APPLY SEALANT
OR TEFLON TAPE
1
Supply to WALL SUPPLY
(1)
is 1/2" NPT. See rough-in above for detailed information.
Install RUBBER SEAL
(2)
onto WALL SUPPLY
(1)
.
Apply sealant or teflon tape to threads of 1/2" NPT supply nipple. Thread WALL SUPPLY
(1)
onto supply nipple making a water tight seal. WALL SUPPLY
(1)
with RUBBER SEAL
(2)
should be tight against finished wall.
2
The ADJUSTABLE SHOWER BAR
(1)
works best if secured to a wall stud or cross brace
within the wall, using the SCREWS
(2)
supplied.
If the ADJUSTABLE SHOWER BAR
(1)
is to be installed on a tile the ANCHORS
(3)
and
SCREWS
(2)
should be used.
Install RUBBER WASHER
(5)
in recess of MOUNTING SUPPORT
(4)
. Secure
MOUNTING SUPPORT
(4)
to wall with SCREWS
(2)
.
For installations on tiled walls:
Use ANCHORS
(3)
and SCREWS
(2)
for securing MOUNTING
SUPPORT
(4)
to finished wall.
The diameter and depth of the mounting hole should be
10mm (3/8”) dia. and 50mm (2”) deep.
Insert the the ANCHORS
(3)
and tap them with
hammer until flush with face of finished wall.
Determine desired height and location (optional) and mark a center line. If MOUNTING
SUPPORT
(4)
is secured to a stud or cross brace drill small pilot holes for SCREWS
(2)
.
IMPORTANT:
Make sure that vertical center line is level.
INSTALL WALL BRACKETS
5
3
2
3
1
5
C/L
C/L
FINISHED WALL
RECESS IN
MOUNTING
SUPPORT
FROM CENTER TO
CENTER OF WALL
BRACKETS
Install ADJUSTABLE SHOWER BAR
(1)
onto installed MOUNTING SUPPORTS
(4)
.
Push ADJUSTABLE SHOWER BAR
(1)
flush against finished wall and tighten
SET SCREWS
(5)
with (2.5mm) HEX WRENCH
(7)
supplied to secure
ADJUSTABLE SHOWER BAR
(1)
to wall.
4
INSTALL ADJUSTABLE SHOWER BAR
INSTALL HOSE AND HAND SHOWER
13
11
12
8
10
9
2
7
4
4
5
Install SEAL
(8)
into COUPLING NUT
(9)
. Connect COUPLING NUT
(9)
to WALL SUPPLY NIPPLE
(10)
and tighten.
INSTALL second SEAL
(11)
into SPRAY HOSE END
(12)
and connect HAND SHOWER
(13)
to SPRAY HOSE END
(12)
.
Hand tighten.
3
M 9 6 8 9 2 7 R e v . 1 . 1
M 9 6 8 9 2 7 R e v . 1 . 1
M 9 6 8 9 2 7 R e v . 1 . 1
2064.724
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2006
IN MEXICO 01-800-839-12-00
CHROME
SATIN NICKEL
002
295
M953169-YYY0A
HAND SHOWER
M962517-YYY0A
24” SLIDE BAR
M962518-YYY0A
HAND SHOWER HOLDER
8888037.YYY
WALL SUPPLY
M962516-YYY0A
END CAP
M962515-0070A
MOUNTING KIT
030782-0020A
HOSE KIT
M962520-YYY0A
CHECK VALVE
