M 9 6 5 0 4 6 R e v. 1 . 3
6530.173
6540.180
3
Insert SPOUT SHANK
(1)
through center hole of
mounting surface, making sure RUBBER GASKET
(2)
is properly positioned in SPOUT BASE
(3)
.
INSTALL SPOUT
4
Assemble RUBBER WASHER
(4)
, BRASS WASHER
(5)
and LOCKNUT
(6)
onto threads of SPOUT SHANK
(1)
from underside of mounting surface.
Align SPOUT
(7, 7a, 7b)
and tighten LOCKNUT
(6)
.
Be sure slot in BRASS WASHER
(5)
is positioned to
the rear as shown.
TEST INSTALLED FAUCET
5
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Turn handles into OFF position and replace AERATOR.
SERVICE
6
CARTRIDGE
SCREEN
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW,
and INDEX.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW
and INDEX.
SPRING
CLIP
STOP
WASHER
90°
Turn off water at
main supply.
CAUTION
TO CHANGE SPOUT FROM RIDGID TO
FULL SWIVEL SPOUT: (6540.180)
Unscrew SPOUT NUT
(1)
and remove SPOUT
(2)
.
Take SPOUT CLIP
(3)
off SPOUT
(2)
and remove RUBBER RING
(4)
.
Replace RUBBER RING
(4)
with seperate PLASTIC RING
(5)
packed
with faucet.
Install SPOUT CLIP
(3)
on SPOUT
(2)
.
Reassemble SPOUT
(2)
to SPOUT BASE
(6)
.
Tighten SPOUT NUT
(1)
.
1
2
3
6
7
7a
7b
4
5
6
2
1
4
3
5
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
6545. Series
(Limited Swivel Spout)
NOTE: For 6545 series faucet make sure Spout is
centered. Spout only rotates 70 degrees from center.
See spout illustration.
70˚
70˚
C/L
Use 3RD WATER COUPLING
(10)
for third water supply
connection. Thghten COUPLING
(10)
. (6530.173)
Press SPOUT SHANK
(1)
into TEE
(11)
making certain
that the O-RING
(8)
is properly seated on SHANK
(1)
.
Push COUPLING
(9)
into TEE
(7)
and attach to SPOUT
SHANK
(1)
and loosely tighten.
COLD
HOT
9
8
11
MOUNTING
LEDGE
10
