Turn off hot and cold water
supplies before beginning.
CAUTION
VALVE INSTALLATION
DRAIN INSTALLATION
1
2
4
LEDGE
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
BODY
5/16''
MIN.
ESCUTCHEON
RUBBER
RING
LOCKNUT
SPOUT
RETAINER
RUBBER
WASHER
RUBBER
GASKET
SINK
Insert BASE or SPOUT shank through
center hole of SINK, making sure
RUBBER GASKET is properly positioned.
SPOUT OR BASE ASSEMBLY
Assemble RUBBER WASHER,
RETAINER, and LOCKNUT onto
threads of SPOUT from underside
of SINK.
Insert LIFT ROD through SPOUT (or
BASE) and slot of RETAINER.
Align SPOUT and tighten LOCKNUT.
Be sure slot in BRASS WASHER is
positioned to the rear as shown.
Prepare TUBE and TEE ASSEMBLY to fit
available VALVE location. If necessary, cut
and/or bend TUBING carefully. Make sure
tube bend is close to the TEE so that it
will not effect the compression joint at
the VALVE.
Place RUBBER RING into ESCUTCHEON
and screw ESCUTCHEON onto VALVE
BODY until snug against internal stop.
Tighten LOCKNUT to secure VALVE
position. Attach COUPLING to TEE
and tighten.
TAIL
PIECE
TEST INSTALLED FAUCET
5
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
TEE
SCREW
O-RING
O-RING
Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
SHANK
Remove COUPLING NUT, FRICTION RING,
and RUBBER FERRULE from each valve and
slide onto tubing.
Push TUBING ends into VALVE side outlets. Insert
VALVES into mounting holes from underside of SINK.
Press TEE onto SHANK of SPOUT making certain that the
SHANK O-RING is properly seated on SHANK.
Slide RUBBER FERRULE, FRICTION RING,
and COUPLING NUT to outlet of VALVE
and tighten COUPLING NUT firmly.
Repeat on other VALVE.
Connect HOT water supply to inlet of left
VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
LOCKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY
(Models 6502, 6902, 6532
and 6932)
(Models 6801 and 6831 only)
PUTTY
FLANGE
DRAIN
PLUG
RUBBER
GASKET
WASHER
LOCKNUT
SINK
3
VALVE INSTALLATION (continued)
6 0 1 8 6 B
STOPPER
Push TAILPIECE down into TRAP
(threaded end up).
Thread LOCKNUT, WASHER and
GASKET onto DRAIN BODY.
Apply a bead of PUTTY to underside
of FLANGE.
Feed DRAIN BODY up through SINK
and thread FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the
PIVOT ROD pointed towards the back
of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP
ROD and tighten THUMBSCREW.
Remove one end of CLIP from PIVOT ROD
by squeezing ends together while sliding.
Insert PIVOT ROD into second or third hole
in EXTENSION and reassemble CLIP.
(EXTENSION may need to be bent.)
Adjust STOPPER height by repositioning
EXTENSION and tightening THUMBSCREW.
FLANGE
SINK
GASKET
PIVOT
ROD
DRAIN
BODY
PUTTY
WASHER
LOCKNUT
TAILPIECE
TRAP
TAILPIECE
CLIP
THUMBSCREW
POP-UP ROD
CLIP
PIVOT
ROD
EXTENSION ROD
SERVICE
6
CARTRIDGE
SCREEN
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90
°
and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW,
and INDEX.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90
°
.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW
and INDEX.
SPRING
CLIP
STOP
WASHER
90
°
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
A m e r i c a n S t a n d a r d I n c . 1 9 9 7
C
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 223-0068
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time
