manualshive.com logo in svg

American Standard Moments 2506.101, Руководство по установке, Страница: 1 / 7

Поделиться
Скачать
American Standard Moments 2506.101 Скачать руководство пользователя страница 1

COLLAR ON

MOUNTING NUT

8

Certified to comply with ANSI A112.18.1

Installation

Instructions

Monoblock Lavatory Faucet with

Speed Connect™ Drain 

Adjustable Wrench

 Screwdriver

Channel Locks

Recommended tools

1

2

4

3

1

1

INSTALL FAUCET

Turn off hot and cold water

supplies before beginning.

CAUTION

GROOVE

(FAUCET

BASE)

MOUNTING SURFACE

6

4

7
5

Seat SEAL 

(1)

 into under side of FAUCET BASE 

(2)

.

Feed FAUCET SUPPLIES 

(3)

, MOUNTING STUD 

(4)

 and DRAIN

CABLE ASSEMBLY 

(8)

 through the mounting hole of lavatory or

mounting surface. 

Fig. A.

From below, push GASKET 

(7)

 and RETAINING WASHER 

(5)

 onto

MOUNTING STUD 

(4)

. Secure Faucet with MOUNTING NUT 

(6)

,

pulling faucet to front of sink, so SUPPLIES 

(3)

 rests against

mounting hole. Before final tightening, make sure collar on 

MOUNTING NUT 

(6)

 is seated into RETAINING WASHER 

(5)

.

Fig. B.

Adjust Faucet so that it is centered. Tighten MOUNTING NUT 

(6)

to complete faucet mounting.

2506.101

MOMENTS

Fig.

 

B.

Fig.

 

A.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain. 

Speed Connect Drain*

•  Fewer parts, installs in less time
•  Never needs adjustment
•  Guaranteed to seal properly the first time, every time.

M968941 Rev. 1.2

Содержание Moments 2506.101








Отзывы:

Нет отзывов