U S 6 0 4 0 6 R E V. 1. 2
2
INSTALL TRIM (SHOWER AND TUB SPOUT)
NOTE; PROTECT FINISH ON SHOWER AND TUB TRIM WHEN INSTALLING.
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull out LEVER BALL from HANDLE BASE.
Unscrew HANDLE BASE and remove ADAPTER
Remove SPRING CLIP.
Lift STOP WASHER, turn 90 and replace.
Replace SPRING CLIP.
Reinstall HANDLE. (See step three).
SPRING
CLIP
STOP
WASHER
90˚
Remove PLASTER GUARDS
(1)
from valve body by unthreading and pulling off.
Apply sealing tape to threads on both ends of SHOWER ARM
(2)
and install
SHOWER ARM
(2)
with SHOWER ESCUTCHEON
(3)
into shower elbow.
Thread SHOWER HEAD
(4)
onto end of SHOWER ARM
(2)
. Push SHOWER
ESCUTCHEON
(3)
against finished wall. Tighten SET SCREW
(5)
.
Remove rough-in nipple from shower elbow.
Remove pipe cap from tub filler pipe. Prepare TUB FILLER PIPE, ELBOW and
1/2" COPPER PIPE. Final length of COPPER PIPE to be 1" from
finished wall.
Push SPOUT ESCUTCHEON
(6)
onto filler pipe flush against finished wall.
Push TUB SPOUT
(7)
onto filler pipe until tight against SPOUT ESCUTCHEON
(6)
.
Tighten clamp screw in SPOUT
(7)
to secure TUB SPOUT
(7)
.
4
1
1
2
4
6
7
7
8
6
5
2
3
ROUGH-IN
NIPPLE
SHOWER
ELBOW
ROUGH-IN
NIPPLE
7
5
6
PIPE CAP
CLAMP SCREW
M
IN US I8M
M
MAXIMUM
M
IN US I8M
M
MAXIMUM
1"
6
3
4
FINISHING INSTALLATION
SERVICE
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90 .
TEST INSTALLED FAUCET
5
Turn HANDLES into "off" position.
Turn on water supplies and check all connections for leaks.
Operate both HANDLES to flush water lines thoroughly.
Check SHOWER HEAD and SPOUT connections for leaks. Operate
DIVERTER for proper operation. Turn handles into OFF position.
Turn VALVE into OFF position.
Push ADAPTER
(1)
into HANDLE BASE
(9)
in a way that the male square on the
ADAPTER
(1)
fits in
he female square of the
HANDLE BASE
(9)
.
Push HANDLE (9) and ADAPTER
(1)
onto VALVE STEM
(3)
.
Check alignment, if not
satisfactory aligned;
Turn VALVE into OFF position.
Push ADAPTER
(1)
into HANDLE
BASE
(2)
in a way that the male
square on the ADAPTER
(1)
fits in
the female square of the
HANDLE BASE
(2)
.
Push HANDLE BASE
(2)
and
ADAPTER (1) onto VALVE STEM
(3)
.
Push CROSS HANDLE
(4, 5)
onto
HANDLE BASE
(2)
.
Install HANDLE SCREW
(6)
and tighten.
Push INDEX CAP
(7, 8)
in top of
CROSS HANDLE.
FOR LEVER HANDLES
FOR CROSS HANDLES
Push out ADAPTER
(1)
carefully.
Turn ADAPTER
(1)
either 45˚ or
90˚ so that male square on
ADAPTER
(1)
catches different
female square in HANDLE BASE
(9)
.
Assemble and tighten HANDLE SCREW
(6)
.
Push INDEX CAP
(7)
in top of HANDLE
(9)
.
INSTALL HANDLES
Install SHOWER ARM, SHOWER ARM FLANGE and TUB SPOUT.
Remove caps from roughing-in nipples.
Remove PLASTER GUARD by turning counter-clockwise and pulling.
If VALVE BODY is roughed in SHALLOW (more than 2-1/2")
screw SLEEVE in ESCUTCHEON facing front of ESCUTCHEON.
If VALVE BODY is roughed in DEEP (less than2-1/2")
screw SLEEVE in ESCUTCHEON facing back of ESCUTCHEON.
Assemble RUBBER RING to ESCUTCHEON.
Screw ESCUTCHEON and SLEEVE onto VALVE COVER against wall.
DEEP ROUGH-IN
LESS THAN
2-1/2"
SLEEVE
SLEEVE
MORE THAN
2-1/2"
ESCUTCHEON
RUBBER
RING
SHALLOW ROUGH-IN
VALVE
BODY
METAL
LEVER
VALVE
COVER
9
3
6
DO: SIMPLY RINSE THE PRODUCT CLEAN
WITH CLEAR WATER. DRY WITH A SOFT
COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT
WITH SOAPS, ACID, POLISH, ABRASIVES,
HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
CARE:
