7 3 0 1 1 4 4 - 1 0 0 R e v . F
10
11
13
- 3 -
12
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
WARNING:
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This
damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine
(calcium hypochlorite).
!
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water to
desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
REPAIR PARTS LIST
NOTE:
"XXX" represents color or trim finish options. Specify when ordering.
Repair parts are determined by toilet tank number which can be found marked inside tank.
TANK NUMBER
PART NO.
DESCRIPTION
4035.516
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
735130-400-XXX0A
738565.426-0070A
738565.427-0070A
7301143-0070A
7381002-400.0070A
7381002-401.0070A
7381003-XXX0A
034783-XXX0A
760127-XXX0A
760130-XXX0A
7381042-0070A
TANK COVER WITH PUSH BUTTON
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
TANK COUPLING KIT #258
DUAL FLUSH VALVE
DUAL FLUSH VALVE
PUSH BUTTON ASSEMBLY - TOP MOUNT
BOLT CAP KIT
TOILET SEAT
TOILET SEAT - SLOW CLOSE
FLUSH VALVE SILICONE SEAL
4035.216
FLUSH BUTTONS ON TANK
• Pressing both buttons at once will flush the full flush amount
1.6 gal/flush or 6L/flush.
• The
Partial Flush Button
should line up over the
blue actuator
on the flush tower in the tank.
• The
Full Flush Button
should line up over the
white actuator
on the flush tower in the tank.
Small button for
liquid waste.
.8 gal/flush
3L/flush
Large button for
solid waste.
1.6 gal/flush
6L/flush
ADJUSTMENTS
a. Adjust water level. Water level should
be adjusted to level indicated on tank by
adjusting float cup.
See Step 11 for water level
adjustment method.
b. Make sure Full Flush Adjustment is at
the bottom setting (0). A higher setting
will result in less water and is not
recommended.
c. Make sure Partial Flush Adjustment is
at the bottom setting (0). A higher setting
will result in less water and is not
recommended.
NOTE:
The Fill Valve does not have a refill
tube. The refill port on the Fluidmaster fill
valve is 100% blocked off. Please ensure that
the correct repair part is used as this fill valve
varies from the standard Fluidmaster 400A.
• To remove Flush Valve, apply slight downward pressure and twist it until the
flush valve disengages from the bayonet.
• To reinstall Flush Valve, reverse the above procedure making sure the blue
(Partial Flush Button) will line up with the Partial Flush Button on the Tank Lid.
VALVE
BODY
ADJUSTABLE
HEIGHT
WATER LEVEL
ADJUSTMENT
ROD
FLUSH
VALVE
PARTIAL
FLUSH
ADJUSTMENT
FULL
FLUSH
ADJUSTMENT
BAYONET
RELEASE
PUSH
BUTTON
VALVE
SEAT
SILICONE
SEAL
TOP
ARM
NIPPLE
SET WATER
LEVEL HERE
Diagram 1
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
CONE WASHER
THREADED
SHANK
SHANK
WASHER
COUPLING NUT
(HAND TIGHT ONLY)
FILL
VALVE
FLOAT
CUP
CRITICAL
LEVEL MARK
("C.L.") MUST
BE 1" ABOVE
OVERFLOW
PIPE
LOCK NUT