background image

M 9 6 8 7 9 6   R e v. 1 . 1

3475.301
3475.501

COLONY/COLONY SOFT

3

5

4

4

Certified to comply with ANSI A112.18.1

Installation

Instructions

Turn off hot and cold water
supplies before beginning.

CAUTION

1

BIDET FAUCET INSTALLATION

Replace UPPER GASKET 

(8) 

and WASHER 

(7)

 . Position

the side threaded outlet rearward and secure MOUNTING
NUT

(6)

. Thread ESCUTCHEON 

(11)

 onto TRANSFER

VALVE 

(9)

until it seats against the BIDET LEDGE. 

Remove MOUNTING NUT 

(6)

, WASHER

 (7)

 and

UPPER GASKET 

(8)

from TRANSFER VALVE 

(9).

Insert TRANSFER VALVE 

(9)

 into the center forward

hole of BIDET.

COLD

HOT

BIDET

LEDGE

10

4

3a

3

8

9

1

5

2

6

11

Roughing-in Dimensions

FINISHED
FLOOR

DIVERTER AND
VACUUM BREAKER
ASSEMBLY

1-1/4 MAX.

1-3/16 DIA.

(C)

(H)

4-1/4

FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS) 

REAR VIEW WITH

WALL REMOVED

8 TO 12

2-1/4
DIA.

SPRAY INSTALLATION

2

Assemble SPRAY BODY 

(1)

 to BIDET. Using putty, seal underside

of SPRAY BODY FLANGE 

(2)

 and secure with NUT 

(3)

.

Thread SPRAY CAP 

(9)

 onto SPRAY BODY 

(1)

.

Thread SPRAY HOSE 

(4)

 with SEAL WASHER 

(5)

 to SPRAY BODY 

(1)

.

Connect other end of HOSE 

(4)

 with SEAL WASHER 

(6)

 to side outlet

NIPPLE

(7)

 of the TRANSFER VALVE 

(8)

.

PUTTY

6

2

7

8

1

9

Tighten LOCKNUTS 

(1)

 with WRENCH 

(5)

 (supplied)

to secure VALVE BODIES 

(3, 3a)

.

Install LOCKNUT 

(1)

 and RUBBER WASHER 

(2)

 onto VALVE BODIES 

(3, 3a)

. From

under side of mounting surface, install VALVE BODY 

(3, 3a)

 through valve mounting

holes. Threads of VALVE BODY 

(3, 3a)

 should extent at least 5/16 of a inch above

mounting surface top. 

Fig. A.

Thread ADAPTER 

(4)

onto VALVE BODIES 

(3, 3a)

until snug against internal stop. If necessary, adjust LOCKNUT 

(1)

.

Place RUBBER RING 

(10)

 into ADAPTER 

(4)

.

MOUNTING

SURFACE

10

2
1

3, 3a

5/16''

MIN.

Fig. A.

7

Adjustable Wrench

 Screwdriver

Channel Locks

Required tools

Tubing Cutter

Phillips Screwdriver

Plumbers' Putty or

Caulking

1

BIDET OUTLINE
IS SYMBOLIC

FINISHED
WALL

1-1/4 O.D. TAILPIECE

DOUCHE
SPRAY

2-1/8

DIA.

ADJ. 1-1/4

TO 2-1/4

3-7/8

5-1/2

1-3/8

DIA.

7/8 DIA.

TRANSFER VALVE

(FOR FLUSHING
RIM OR SPRAY)

4

Bidet Faucet and Transfer Valve

with SpeedConnect™ Drain

Congratulations on purchasing your American
Standard faucet with Speed Connect drain,  a
feature found only on American Standard faucets.

*Your new American Standard faucet is designed to work only with the SpeedConnect drain. 

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

SpeedConnect Drain*

•  Fewer parts, installs in less time
•  Never needs adjustment
•  Guaranteed to seal properly the first time, every time.

Содержание Colony/Colony Soft 3475.301







Отзывы: