WARNING: These products may present a possible shock
or fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with the
owners manual, current electrical codes and/or the
current National Electric Code (NEC).
IMPORTANT
The following instructions are provided to assure safe
installation and operation of the LED Mini Swivel Series.
Please read carefully before connecting or installing this
product.
1. The LED Mini Swivels are a safe low voltage lighting
system that are suitable for indoor locations only.
2. Do not mount or support these fixtures in a manner
that can cut the outer jacket or damage wire insulation.
3. Always make sure power is disconnected from the LED
fixtures before cutting, mounting, attaching terminal
block, attaching end cap or modifying in any way.
4. Do not exceed the maximum capacity of the 350mA
DC power supply used for any series configuration.
SPECIFICATIONS
• 1 – 10 watts can be powered by one LED-DR10-350PI
• 1 – 10 watts can be powered by one LED-DR10-350AL
• 6 – 12 watts can be powered by one LED-DR12-350
• 10 – 18 watts can be powered by one LED-DR18-350
• 3-12 LEDs can be powered by each LED-DR18-350D
• Constant current LED driver (350mA DC) is required
• Series wiring configuration only (do not wire in parallel)
• Cut-out size: 1-7/8” for LMS and LMV fixtures; 2-3/4“
for LMS-3. (All styles for recessed applications only.)
• Wattages: LMS, LMV = 1.25 each; LMS-3 = 3.75 each
BEFORE YOU START
• Always make sure the LED lights are disconnected
from the power source before wiring.
• Determine the number and locations of fixtures your
application will require. There are multiple power
connection configurations and accessories that allow
many installation options. See reverse side prior to
installation to determine the best configuration for each
installation. Remember, for every run, add total
wattages and do not exceed the capacity of the
power supply!
****FOR HARDWIRE INSTALLATIONS, SEE OTHER SIDE ****
FOR PLUG IN INSTALLATIONS (using LED-DR10-350PI)
1. Utilizing a good pair of shears, cut the Plastic connector off
the power connector (LED-CON2-350, LED-CON3-350 or
LED-CON6-350). Do NOT cut the plastic connector off of the
Mini Swivel Lights! Do NOT cut the plastic connector off of
any power connectors for hardwire power supplies! See
other side for hardwire installation instructions.
2. Strip the insulation back 3/16” on lead wires.
3. Place the stripped leads of the power connector into one side
of the TL-CONBLK2 connector (see Figure 1) and tighten screws.
4. Place stripped leads of plug-in driver LED-DR10-350PI into
the other side of TL-CONBLK2 connector, being sure to match
polarity and tighten screws. Connect solid red power connector
lead to power supply connector marked with red. Black/red
striped power connector lead goes to black power supply lead.
See Figures 2 and 3.
5. Check that the male Plastic connector of each LED Mini Swivel
fixture is in operable condition. If in operable condition, insert
male Plastic connector into an open female port of the power
connector.
6. When powering only one LED light, it is necessary to insert an
end cap, LED-END-350, into the other open port to complete
the series wiring.
7. When powering LED Mini Swivel light systems, every port of
each power connector must be connected to an end cap,
another power connector or a light. See Figure 3.
ATTACHING JUNCTION BOX
1. Each TL-CONBLK2 (shown in Figures 1 and 2) can be placed in
a junction box (FSL-BOX) if desired.
2. Disconnect power from transformer.
3. Place TL-CONBLK2 assembly into top of FSL-BOX.
4. Make sure TL-CONBLK2 assembly fits into junction box and
enclose with FSL-BOX bottom. Tighten four screws through
bottom cover plate into FSL-BOX housing.
LED MINI SWIVEL SERIES
Installation instructions for LMS, LMV, LMS-3, LMS-3KIT, LMV-3KIT and LMS-3-3KIT series fixtures
RV-1125
Figure 2
CUT OFF PLASTIC ONLY
WHEN
USING PLUG-IN DRIVER
Figure 3
www.americanlighting.com
Figure 1
Lead wire to power connector
TL-CONBLK2
Connect red to red; and
black/red stripe to black.
See also reverse for additional connectors.
MOUNTING LED MINI SWIVEL SERIES
1. Always make sure power is disconnected
before modifying, mounting or installing a
series of LED Mini Swivel Lights.
2. Drill a 1-7/8” hole for LMS or LMV fixtures;
or 2-3/4” hole for LMS-3 fixtures.
3. Open steel spring clips.
4. Insert LED Mini Swivel into hole.
5. Make sure that the fixture’s lead wire is not
in contact with sharp objects.
6. Maximum wattage per series is
dependent upon the power supply. Add the
number of lights and respective wattages to
assure you do not exceed the maximum
wattage.
