WARNING
: These products may present a possible shock
or fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with the
owners manual, current electrical codes and/or the
current National Electric Code (NEC).
IMPORTANT
The following instructions are provided to assure safe
installation and operation of LED Bullets. Please read
carefully before connecting or installing this product.
1. The LED Bullets are a safe low voltage lighting system
that are suitable for indoor locations only.
2. Do not mount or support the LED Bullet in a manner
that can cut the outer jacket or damage wire insulation.
3. Always make sure power is disconnected from the LED
Bullets before cutting, mounting, attaching terminal
block, attaching end cap or modifying in any way.
4. Do not exceed the maximum capacity of the 350mA
DC power supply used for any series configuration.
SPECIFICATIONS
• 1 – 8 Bullets can be powered by each LED-DR10-350PI
• 1 – 9 Bullets can be powered by each LED-DR12-350
• 1 – 14 Bullets can be powered by each LED-DR18-350
• Two runs of 1 – 14 Bullets can be powered by each
LED-DR36-350HW
• Constant current LED driver (350mA DC) is required
• Series wiring configuration only (do not wire in parallel)
• Hole mount size: 1” (for recessed applications
only
)
• Fixture height: 13/16”
• Wattage per Bullet: 1.25
BEFORE YOU START
•
Always make sure the LED Bullet is disconnected
from the power source before wiring.
• Determine the number of LED Bullets your application
will require. There are multiple power connection
configurations and accessories that allow many
installation options. See reverse side prior to installation
to determine the best configuration for each installation.
Remember, in any case, do not exceed the capacity of the
power supply used for any single run.
****FOR HARDWIRE INSTALLATIONS SEE OTHER SIDE ****
FOR PLUG IN INSTALLATIONS (using LED-DR10-350PI)
1. Utilizing a good pair of shears, cut the Molex connector off
the power connector (LED-CON2-350, LED-CON3-350 or
LED-CON6-350).
Do NOT cut the molex connector off of the
Bullet Lights!
Do NOT cut the molex connector off of any
power connectors for hardwire power supplies!
See reverse
side for hardwire installation instructions.
2. Strip the insulation back 3/16” on lead wires.
3. Place the stripped leads of the power connector into one side
of the TL-CONBLK2 connector (see Figure 1) and tighten screws.
4. Place stripped leads of plug-in driver LED-DR10-350PI into
the other side of TL-CONBLK2 connector, being sure to match
polarity and tighten screws. Connect solid red power connector
lead to power supply connector marked with red. Black/red
striped power connector lead goes to black power supply lead.
See Figures 2 and 3.
5. Check that the male Molex connector of each LED Bullet is in
operable condition. If in operable condition, insert male Molex
connector into an open female port of the power connector.
6. When powering only one Bullet, it is necessary to insert an
end cap, LED-END-350, into the other open port to complete
the series wiring.
7. When powering Bullets, every port of each power connector
must be connected to an end cap, another power connector or
a Bullet. See Figure 3.
ATTACHING JUNCTION BOX
1. Each TL-CONBLK2 (shown in Figures 1 and 2) can be placed in
a junction box (FSL-BOX) if desired.
2. Disconnect power from transformer.
3. Place TL-CONBLK2 assembly into top of FSL-BOX.
4. Make sure TL-CONBLK2 assembly fits into junction box and
enclose with FSL-BOX bottom. Tighten four screws through
bottom cover plate into FSL-BOX housing.
LED BULLETS
Installation instructions for 024 Series and 024-3KIT series
RV-0904KB
Figure 2
CUT OFF MOLEX
ONLY
WHEN
USING PLUG-IN DRIVER
Figure 3
www.americanlighting.com
Lead wire to power connector
TL-CONBLK2
Figure 1
Connect red to red; and
black/red stripe to black.
MOUNTING LED BULLET
1. Always make sure power is disconnected
before modifying, mounting or installing a series
of LED Bullets.
2. Drill a 1” hole in mounting surface.
3. Insert Bullet into cabinet.
4. Make sure that the wire is not in contact with
sharp objects.
5. Maximum wattage per series is dependent
upon of the power supply. Add the number of
bullets and respective wattage to assure you do
not exceed the maximum wattage.
6. For best results in situations where Bullets are
mounted continually facing down, affix the fixture
with a small amount of silicone to secure the
fixture in place.
