American Energy Systems T-40 AC Скачать руководство пользователя страница 14

CLEANING INSTRUCTIONS 

 

NOTE:  BE SURE THE STOVE IS TURNED OFF, THE POWER CORD IS 
UNPLUGGED, AND THE UNIT IS COLD BEFORE CLEANING OR SERVICING. 
 
RECOMMENDED CLEANING PERIODS: 

A.

 

The heat exchange tubes in the stove should be cleaned weekly. 

B.

 

The fire box should be cleaned every 7 to 10 days. 

C.

 

The interior ash chambers should be inspected and cleaned as needed. 

D.

 

The chimney pipe and cap should be checked annually for soot buildup. 

E.

 

Combustion blower should be cleaned as needed.  Check as least semi-
annually. 

 

DISPOSAL OF ASHES: 

Ashes should be placed in a metal container with a tight fitting lid.  The closed container of ashes 
should be placed on a noncombustible floor or on the ground, well away from all combustible 
materials, pending final disposal.  If the ashes are disposed by burial in soil or otherwise locally 
dispersed, they should be retained in the closed container until all cinders have been thoroughly 
cooled. 
 

WARNING:  MANY HOME VACUUM CLEANERS ALLOW ASH TO ESCAPE INTO 
THE ROOM AIR; HOWEVER, VACUUMING IS RECOMMENDED OCCASIONALLY 
TO AID IN SEASONAL CLEANING AND KEEP THE UNIT FREE OF EXCESS ASH.  
DISCARD THE VACUUM BAG AFTER EACH USE ON THE STOVE.

 

 

I. FIREBOX 

     A.       Open the door, sweep or vacuum 
 

     Out the ash buildup.  Remove the  

 

     Firepot and empty, inspect all air 

 

     Holes and clean if blocked.  Inspect 

 

     Under the firepot for build up of ash. 

B.

 

Replace the firepot in the stove.   

C.

 

Periodically inspect the ash chambers 
“A”, “B”, and “C” by removing the 
inspection caps.     

D.

 

Remove the 3 wingnuts, bracket and 
brick panels.  The ash chambers can  
be removed from the firewall for a  
more thorough cleaning. 

 

 
 
 
 
 
WARNING:  Failure to clean the stove is a leading and preventable cause of stove 
malfunctions.  Fuel types and installations may dramatically affect the cleaning intervals 
required for your stove.  Sampling different brands of fuel to find the cleanest burning fuel 
available in your area can greatly reduce the amount of maintenance required. 
 

(15) 

Содержание T-40 AC






















Отзывы: