manualshive.com logo in svg

American Dynamics RHODUL-03E, Руководство по установке

Поделиться
Скачать
American Dynamics RHODUL-03E Скачать руководство пользователя страница 3

 

SPEEDDOME ULTRA OUTDOOR HOUSING 

8200-0184-10, REV. C 

CONTINUATION OF INSTALLATION GUIDE 

3 of 12

 

SpeedDome

®

 Ultra 

Outdoor Housing 

Installation Guide - Continued 

RHODUL-03E/-03VRE (Clear Bubble) 
RHODUL-04E/-04VRE (Smoked Bubble) 

Contents: 

To the Installer....................................................... 3

 

About the Product.................................................. 3

 

Parts Supplied ....................................................... 3

 

Tools Required ...................................................... 3

 

Warnings and Cautions......................................... 4

 

Preventing Condensation...................................... 5

 

Parts List for Authorized Users ............................. 5

 

Connector Pin Assignments.................................. 6

 

Cable Requirements.............................................. 6

 

Manual Heater Operation...................................... 7

 

Housing Termination ............................................. 8

 

Troubleshooting..................................................... 9

 

Specifications ...................................................... 11

 

Declarations ........................................................ 12

 

 

 

© 2005 Sensormatic Electronics Corp. 

To the Installer 

This guide assumes that the outdoor mounting 
structure to which the housing is attached is in 
place and that data and power cables have been 
pulled to the installation site. To install the outdoor 
mounting structure, see documents shipped with 
the structure. 

About the Product 

The outdoor housing has a sunshield cover and 
bubble that protect the SpeedDome Ultra dome 
camera. Tamperproof screws affix the bubble to 
the housing. 
The housing is temperature controlled and 
weatherproof. A built-in thermostat and heater 
prevent ice from forming on the outside of the 
bubble. 
The standard version has one alarm input and one 
SPDT relay. The vandal-resistant version adds 
three more alarm inputs. Surge protection is 
provided on all external lines, including video. 

Parts Supplied 

•

  Housing assembly 0100-2468-02 

•

  Bubble assembly 0404-0083-01/-02 

•

 Tamperproof 

drive 

1400-0149-01 

•

  Install kit 0351-2183-04 

Purchase or Supply Separately 

Male BNC connector 

Tools Required 

•

  6.6mm (1/4in) fixed-handle  

nut driver for Torx bit 

•

  Wire cutters and strippers 

•

  2.5mm (0.1in) slotted screwdriver 

Содержание RHODUL-03E













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды