manualshive.com logo in svg

American Dynamics RAS918LS, Инструкция по установке и обслуживанию, Страница: 1 / 37

Поделиться
Скачать
American Dynamics RAS918LS Скачать руководство пользователя страница 1

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME 

8200-0184-14, REV. A 

INSTALLATION AND SERVICE GUIDE 

1 of 37 

SpeedDome

®

 Ultra VII EIS 

Day/Night Camera Dome 

Installation and Service Guide 

Figure 1. SpeedDome Ultra VII EIS Day/Night 

Camera Dome 

 

Camera Dome Product Codes 

Product Description 

RAS918LS 

DAY/NIGHT, EIS, 60HZ, 23X, NO BASE, 
BLACK 

RAS918LSP 

DAY/NIGHT, EIS, 60HZ, 23X, STD BASE, 
BLACK (RUPTB) 

RAS918LSI DAY/NIGHT, 

EIS, 60HZ, 23X, I/O BASE, 

BLACK (RUIOB) 

 

 

 

 

 

 

 

 

 

 

 

 

© 2005 Sensormatic Electronics Corp. 

Contents 

About this Guide ....................................................1

 

About the Camera Dome .......................................2

 

Cable Requirements ..............................................7

 

Install/Removal Tool for Base with I/O Board........8

 

Power-Up Routine..................................................9

 

Synchronizing Domes ............................................9

 

Diagnostic LEDs ....................................................9

 

Warnings and Cautions .........................................9

 

Indoor Installation.................................................11

 

Using the Install/Removal Tool ............................20

 

Troubleshooting Indoor Domes ...........................22

 

Parts List for Authorized Users ............................32

 

Specifications-Indoor Dome.................................34

 

Specifications-23X Camera with EIS ...................35

 

Declarations .........................................................36

 

Appendix A: Vicon Wiring Configurations ............37

 

 

About this Guide 

This guide explains how to connect the camera 
dome to a mounting base and how to service it. 

It does not explain how to: 

•

  Determine a mounting location for the camera 

dome. The mounting location is determined by 
customer requirements; therefore, this 
information is provided separately. 

•

  Attach the mounting base. There are two types 

of mounting bases. See information shipped 
with the base. 

•

  Assemble housings and structures used with 

this camera dome. See information shipped with 
the housing and structure. 

•

  Program the camera dome. See operator's 

guide shipped with the dome. 

 

Mounting 
Base 

Housing 

Eyeball 

Содержание RAS918LS






































Отзывы:

Нет отзывов