American Dynamics ADSDUHOC Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 10

American Dynamics ADSDUHOC Скачать руководство пользователя страница 8

SPEEDDOME ULTRA OUTDOOR HOUSING

8200-0492-02, REV. B

INSTALLATION GUIDE - CONTINUATION

10 of 12

SensorNet Data Connections

Pin Color

Designation

1-4 —

Not

used.

5 White/Orange

SensorNet

(unshielded)

6 White/Yellow

SensorNet

(unshielded)

4. Check fans. Are they on?

- YES:

Continue.

- NO: Go to “Fans Do Not Turn” procedure

next.

5. Check video on monitor. Does the picture roll?

- YES: Use the video controller or switcher to

synchronize video vertical sync phases of all
domes to the ac line. For specific
instructions, see the installation and service
manual for the controller or switcher.

- NO:

Continue.

Is the picture normal?
- YES: See “Detailed Troubleshooting” in the

installation and service manual supplied with
the dome.

- NO: See “Poor or No Video” on this page.

Blowers Do Not Turn

Follow steps until the problem is corrected. See
page 5 to order parts.

1. Determine if the dome camera is receiving

power. Look for evidence such as a picture on
the video monitor or dome movement.

2. Detach the dome camera to access the

environmental PC board.

Note:

Power to blowers comes from the dome.

Fans will not function with the dome removed.

CAUTION:

Touch the metal housing

before handling the environmental PC
board.

3. Verify power is reaching the housing. Press and

hold switch SW2 and observe the green (ac
power) LED; it should glow steadily. If not,
check power at the J-box and check that the ac
cable is plugged into connector P7 on the top
side of the environmental PC board.

4. Check the blower connector. Is it plugged into

connector P5 on other side of the environmental
PC board?
- YES: Replace blower/heater assembly 0304-

2906-01. Remove two screws to remove
assembly.

- NO: Plug the connector in, reinstall the

environmental PC board, and reconnect the
dome. If blower/heater fans still do not work,
replace the blower/heater assembly.

Picture is Grainy or Discolored

Check the blowers. If they are not turning, the
camera dome may be overheating. See “Dome
Does Not Respond to Commands” on page 9.

Poor or No Video

See “Dome Does Not Respond to Commands” on
page 9.

«
...
6
7
8
9
10
»

Содержание ADSDUHOC











Отзывы:

Нет отзывов