background image

ADJ Products, LLC  -  www.adj.com  - Pixel Pulse Bar Instruction Manual Page 9

ADJ Products, LLC  -  www.adj.com  - Pixel Pulse Bar Instruction Manual Page 10

  Pixel Pulse Bar                                              System Menu

ENTER.
2. “SH X” will now be displayed. “X” representing a number 

between 0-8. Shows 1-8 are preset shows, while “SH 0” is random 

show. Press the UP or DOWN buttons to find your desired show.
3. Once you have found your desired show press ENTER, and 

then press and hold the MENU button for at least 3 seconds to 

confirm. 

 

SOUN

 - In this submenu you can activate sound active 

mode. 
1.  Press  the  MENU  button  until  “SOUN”  is  displayed,  press 

ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or 

DOWN buttons to select one or the other.   
3. When you have made your selection, press the ENTER, and 

then press and hold the MENU button for at least 3 seconds to 

confirm. 

SENS -

 Sound sensitivity control

1. Press the MENU button until “SENS” is displayed, press ENTER.
2. The display will show a number between 0-100. Press the UP or 

DOWN buttons to adjust the sound sensitivity. 0 being the least sensi-

tive and 100 the most sensitive.
3. Press the ENTER, and then press and hold the MENU button for at 

least 3 seconds to confirm.

DNST

 - This mode can be used as a precaution mode, that 

in case the DMX signal is lost, the operating mode chosen in 

the setup is the running mode the fixture will go into when 

the DMX signal is lost. You can also set this as the operat-

ing mode you would like the unit to return to when power is 

  Pixel Pulse Bar                                              System Menu

applied.  
1.  Press  the  MENU  button  until  “DNST”  is  displayed,  press 

ENTER.
2. Either “MASL”, “BLND”, or “LAST” will be displayed. Choose 

an operating mode you would like the unit to start up in when 

power is applied or the DMX signal is lost.
• MASL  (Master Slave) - If the DMX signal is lost or power is 

applied, the unit will automatically go into Master Slave mode.
• BLND (Blackout) - If the DMX signal is lost or power is applied, 

the unit will automatically go into stand by mode.
• LAST (Last State) - If the DMX signal is lost the fixture will stay 

in the last DMX set up. If power is applied and this mode is set, 

the unit will automatically go into the last DMX set up.   
3. Press ENTER to confirm your desired set up. 

LED

 - With this function the LED display will turn off after 2 

minutes.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or 

DOWN buttons to select “ON” to keep the LED display on at all 

times, or “OFF” to allow the LED display to turn off after 2 min-

utes. Press any button to turn on the LED display again.  
3. Press ENTER, and then press and hold the MENU button 

for at 

least three seconds

 to confirm.

DISP

 - This will “flip” the LED display 

1. Press the MENU button until “DISP” is displayed, press 

ENTER.
2. When “DISP” is displayed the LED display will remain normal, 

Содержание Pixel Pulse Bar











Отзывы: