©
American DJ Supply
®
- www.americandj.com - P64 BlinderRGB Instruction Manual Page 8
©
American DJ Supply
®
- www.americandj.com - P64 BlinderRGB Instruction Manual Page 7
Operating Modes:
You can use the P64 BlinderRGB in either a stand alone mode or a
master/slave configuration, there are 4 modes to choose from:
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs, with or without a strobe effect.
• Auto Mode - The unit will automatically chase through the different
colors, with or without a strobe effect.
• RGB Mode - Choose a single color or colors to stay static or
strobe.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the Elation
®
Show Designer™.
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the con-
trolling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of
the unit. Use standard XLR microphone cables to link your
units together. Remember that the Male XLR connector is the
input and the Female XLR connector is the output. The first
unit in the chain (master) will use the female XLR connector
only. The last unit in the chain will use the male XLR
connector only.
2. Set dipswitches #1 and #10 to the “ON” position, on the “Master”
unit.
3. For the “Slave” unit(s), dipswitch #10 must remain in the “Off”
position, other then that you may set the dipswitch(es) at any
setting.
4. Connect the “Slave” unit or units and they will automatically start
to follow the “Master.”
Sound Active Mode:
In this mode the P64 BlinderRGB will react to sound, and chase
through the different colors.
P64 BlinderRGB Operating Instructions
1. Plug the fixture in and put dipswitch #10 in the “ON” postion and
follow the dipswitch settings on page 9 for the different sound
active programs.
If you want the unit to strobe, put dipswitch #7
into the “ON” position also.
2. The fixture will now change via sound.
Auto Mode:
1. Plug the fixture in and put dipswitches # 9 and 10 in the “ON”
position, and dipswitch #8 in the “OFF” position.
If you want the
unit to strobe, put dipswitch #7 into the “ON” position also.
2. Adjust the speed via dipswitches 1-6..
RGB (Red, Green, and/or Blue) Mode:
1. Plug the fixture in and put dipswitches #8, 9, and 10 in the “ON”
postion. Then follow the instructions below to activate the color or
colors of your choice.
If you want the unit to strobe, put dip-
switch #7 into the “ON” position also.
2.
RED -
Dipswitch #1 in the “ON” position will give you an intensity
of 25%. Dipswitch #2 in the “ON” position will give you an intensity
of 50%. Dipswithes #1 and #2 in the “ON” position will give you an
intensity of 100%.
GREEN -
Dipswitch #3 in the “ON” position will give you an inten-
sity of 25%. Dipswitch #4 in the “ON” position will give you an
intensity of 50%. Dipswithes #3 and #4 in the “ON” position will
give you an intensity of 100%.
BLUE -
Dipswitch #5 in the “ON” position will give you an intensity
of 25%. Dipswitch #6 in the “ON” position will give you an inten sity
of 50%. Dipswithes #5 and #6 in the “ON” position will give you an
intensity of 100%.
DMX Mode:
Operating through a DMX controller give the user the freedom to cre-
ate their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation
®
Show Designer™ or the Elation
®
DMX Operator.™
2. The P64 BlinderRGB uses seven DMX channels to operate see
P64 BlinderRGB Operating Instructions
