background image

  Flat Par Tri7X                                           Trouble Shooting

  Flat Par Tri7X                                                        Cleaning

  Flat Par Tri7X                                        Fuse Replacement

©

American DJ

®

  -  www.Americandj.com  - Flat Par Tri7X User Manual Page 17

©

American DJ

®

  -  www.Americandj.com  - Flat Par Tri7X User Manual Page 18

Listed below are a few common problems the user may encounter, 

with solutions.
Unit not responding to DMX:

1.  Check that the DMX cables are connected properly and are    

  wired correctly (pin 3 is “hot”; on some other DMX devices    

  pin 2 may be ‘hot’). Also, check that all cables are connected   

  to the right connectors; it does matter which way the inputs    

  and outputs are connected.
Unit does not respond to sound:

1.  Quiet or high pitched sounds will not activate the unit.

2.  Make sure that Sound Active mode is activated.

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal optical lenses must be carried out periodically to optimize light 

output.  

1.   Use normal glass cleaner and a soft cloth to wipe down the 

  outside casing.

2.   Clean the external optics with glass cleaner and a soft cloth 

  every 20 days.

3.  Always be sure to dry all parts completely before plugging 

  the unit back in.

Cleaning frequency depends on the environment in which the fixture 

operates (i.e. smoke, fog residue, dust, dew). 

Disconnect the unit from its power source. Remove the power cord 

from the unit. Once the cord has been removed, you will find that the 

fuse holder is located inside the power socket. Insert a flat-head screw 

driver into the power socket and gently pry out the fuse holder. Remove 

the bad fuse and replace with a new one. The fuse holder also has a 

holder for a spare fuse.

With  this  feature  you  can  connect  the  fixtures  to  one  another 

using the IEC input and output sockets. The quantity that can be 

connected is 24 fixtures maximum. After 24 fixtures you will need 

to use a new power outlet. They must be the same fixtures. DO 

NOT mix fixtures.

  Flat Par Tri7X                               Power Cord Daisy Chain

  Flat Par Tri7X                                                    Installation

The Flat Par Tri7X is fully operational in three different mounting 

positions, hanging upside-down from a ceiling, hanging sideways on 

trussing, or set on a flat level surface. The unit should be mounted 

using a mounting clamp (not provided), affixing it to the mounting 

bracket that is provided with the unit. Always ensure that the unit is 

firmly fixed to avoid vibration and slipping while operating. Always 

ensure that the structure to which you are attaching the unit is secure 

and is able to support a weight of 10 times the unit’s weight. Also, 

always use a safety cable that can hold 12 times the weight of the 

unit when installing the fixture.

The equipment must be installed by a professional, and it must be 

installed in a place where it is out of the reach of people’s grasp.

Содержание Flat Par CWWW18











Отзывы: