background image

ADJ Produc

t

s, LLC  -  www.adj.com  - Event Bar Q4 Instruction Manual Page 11

active mode.

1. Press the MENU button until “Sound State” is displayed, press 

ENTER.
2.  Either  “On”  or  “Off”  will  now  be  displayed.  Use  the  UP  or 

DOWN buttons to toggle between “On” and “Off”. 
3. Press ENTER to confirm your selection, the press and hold the 

MENU button to activate. 

Sound Sense

 - In this mode you can adjust the sound 

sensitivity of the sound active mode.

1.  Press  the  MENU  button  until  “Sound  Sense”  is  displayed, 

press ENTER.
2. Press the UP or DOWN buttons to adjust the sensitivity level. 

The sensitivity level can be adjusted between 0 (the lowest) and 

100 (most sensitive). 
3. Press ENTER to set you desired level. 

DMX  State

 - 

This mode can be used as a precaution 

mode, that in case the DMX signal is lost, the operating mode 

chosen in the setup is the running mode the fixture will go 

into when the DMX signal is lost. You can also set this as 

the operating mode you would like the unit to return to when 

power is applied.

  

1. Press the MENU button until “DMX State” is displayed, press 

ENTER.
2. Either “Master/Slave”, “Blackout”, or “Last State” will be dis-

played. Choose an operating mode you would like the unit to 

start up in when power is applied or the DMX signal is lost.
• Master/Slave - If the DMX signal is lost or power is applied, the 

unit will automatically go into Master Slave mode.

ADJ Produc

t

s, LLC  -  www.adj.com  - Event Bar Q4 Instruction Manual Page 10

Show  Mode

 

- Show modes 0-8 (Factory programs). 

Show mode can run with or without sound active mode 

active. 

1. Press the MENU button until “Show Mode” is displayed, press 

ENTER.
2. “Show X” will now be displayed, “X” representing a number 

between 0-8. Programs 1-8 are factory programs, while “Show 

0” is random mode. Press the UP or DOWN buttons to find your 

desired show.

Install Mode

 

- This will let you set your unit as a master 

or slave in a master/slave configuration. 

1. Press the MENU button until “Install Mode” is displayed, 

press ENTER. Either “INS 1”, “INS 2” or “INS 3” will be dis-

played.

 • INS 1 - Long range beam (ceiling hanging)

 • INS 2 - Short range beam (ceiling hanging)

 • INS 3 - Front range beam (for truss or wall mounting)
2. Press the UP or DOWN buttons until your desired installation 

setting is displayed, and press ENTER to confim.

Dimmer Mode

 

- In this mode you can select the dimmer 

curve. See page 21 for the different dimmer modes.

1.  Press  the  MENU  button  until  “Dimmer  Mode”  is  displayed, 

press ENTER.
2. The current dimmer mode will be displayed.
3. Press the UP or DOWN buttons to find your desired dimmer 

mode and press ENTER to confirm.

Sound State

 - In this mode the unit will run in sound 

 Event Bar Q4 

 

                                System Menu

 Event Bar Q4 

 

                                System Menu

Содержание Event Bar Q4















Отзывы: