background image

American DJ

®

AUDIO • DCD-PRO200™ INSTRUCTIONS MANUAL • PAGE 9

17)

FORWARD SKIP BUTTON -

Use this button to 

skip to the next track on  the CD.

18) 

PLAYER 2 REMOTE CONNECTOR

- Connect 

to player 2 connector on transport assembly.

19) 

PLAYER 1 REMOTE CONNECTOR

- Connect 

to player 1 connector on transport assembly.

C. LCD

(figure 5)

1)

PLAY INDICATOR (      ) - 

The PLAY indicator 

lights during playback.

2)

PAUSE INDICATOR (     ) - 

The PAUSE 

indicators light during pause or cue mode.

3)

CUE INDICATOR - 

The CUE indicator lights 

during CUE mode or PAUSE mode, flashes when 
CUE point is changed.

4)

ELAPSED INDICATOR -

It indicates that the time 

shown on the display is the elapsed time.

5)

TOTAL INDICATOR - 

It indicates that the time 

shown on the display is the elapsed time.

6)

BAR INDICATOR -

These ten indicator provide a 

visual display of the approximate position of the

FUNCTIONS & CONTROLS 

CONT.

pickup within the current track.

7)

REMAIN INDICATOR - 

It indicates that the time 

shown on the display is the remaining time of the 
playing track.

8)

SINGLE INDICATOR - 

When the indicator light, 

playback will stop at the beginning of the track.

9)

PROGRAM INDICATOR -

The PROGRAM

indicator lights when program mode is set.

10)

PITCH INDICATOR -

When the indicator lights, 

the pitch adjustment is enabled.

11)

LOOP INDICATOR - 

When in loop mode this 

indicator will glow.

12)

TRACK INDICATOR 

- Indicates the current track 

that is playing, cued, or in pause mode.

13)

MINUTES INDICATOR 

- Display current minutes. 

14)

SECONDS INDCTORS 

- Displays current seconds

15)

FRAME INDICATOR

s - Displays current frames

16) 

PITCH PERCENTAGE 

- This displays the amount 

of pitch being applied to the track. This is adjusted 
by the PITCH SLIDER.

PREPARATIONS

1. Check that the carton contains the following items:      

1)

Main unit

2)

Control unit

3)

Operating instructions ( this booklet)

4)

Two sets of RCA cables.

5)

Two Control cords (6 feet / 1.8 meters)

2. Installing the Units 

Mount the units onto your console or rack with 19" EIA rack rails.

CAUTION:

• The player will work normally when the main 

unit is mounted with the front panel within 
15 degrees of the vertical plane. If the unit is 
tilted excessively, discs may not be loaded or 
unloaded properly. 

(Figure 6)

• The control panel's LCDs are designed to be 

clearly visible within the angles shown in 

Figure 7

. Mount the control unit so that the 

visual angle is within this range.

Fig. 6

Fig. 7

Содержание PROformer DCD-PR200 MK2














Отзывы: