background image

  

   

Power switch on/off

Upper position: Power on
Lower position: Power off
Middle position: Auto on  

At this position the subwoofer amplifier is in a stand by mode, awaiting an input 

signal. When there is no signal, the amplifier is shut down. As soon as the signal 

appears, the amplifier switches on. If signal is absent, the amplifier will shut 

down automatically after a pre-determined period of time. The power indicator 

is red when the switch is at  OFF  position, and green when the switch is at  ON  

or  AUTO  position.

   

Volume Control

Use this control to balance the level of the woofer with the level of your main 

speakers.

    

Crossover Frequency control

       If you are using small loudspeakers (4

to 6

 woofers) in your main system, you 

will need to set the crossover frequency at a high position (100 to 160 Hz). If 

your main speakers have larger woofers (8

 and above) you will need to set the 

crossover frequency to much lower position (40 to 80 Hz). Generally, the larger 

the speaker, the greater the low frequency output will be. If the frequency 

control is set too high, the bass will appear 

boomy

 due to outputs of 

subwoofer and main speakers overlapping each other. If it is set too low, the 

bass will be ill defined and the subwoofer will sound detached from the rest of 

the system.

   

Phase Control

Use this control to determine the best possible bass performance of your system. 
There can be interference between your main speakers and subwoofer at the 
frequency where they cross over due to placement, room acoustics and type of 
main speakers used. By carefully positioning the subwoofer in the room in 
combination with the level and crossover control, you should be able to get a 
seamless transition between your main speakers and subwoofer. Start with the 
full anticlockwise 0 position. This means that the subwoofer will push out 
positive pressure wave corresponding to a positive electrical input. The              
180  full clockwise position inverts this so the subwoofer will put out a negative 

1-3

Содержание C -11












Отзывы: